manualshive.com logo in svg

Edwards EXC120, Инструкция по эксплуатации

Поделиться
Скачать
Edwards EXC120 Скачать руководство пользователя страница 42

D396-14-880 Issue J

Page 34

© Edwards Limited 2008. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

4.3

Bakeout band control (EXC120/300/300M only)

Note:

As described in 

Section 3.8

, you must insert a suitably rated fuse into the bakeout band fuse holder before 

you can use a bakeout band.

Press the Heater switch on the front panel of the Controller (Figures 

1

 and 

2

, item 2) to select the bakeout band on.

The Controller will switch on the electrical supply to the bakeout band when the EXT pump speed has reached the 
Normal speed setpoint. The electrical supply to the bakeout band will switch off if the pump speed drops to below 
the Normal speed setpoint, if the Controller is switched off, or if the Controller trips into Fail condition or Axial 
Emergency condition.

The LED on the Heater switch is on when the electrical supply to the bakeout band is on.

4.4

Operation with high inlet pressure

If the EXT pump inlet pressure rises, the power supplied by the Controller to the pump-motor will increase to 
counteract the gas frictional load. The pump rotational speed will remain constant until the Controller peak power 
level is reached; beyond this power level, the speed of the pump will start to reduce.

If the pump speed falls to below 50% of its full rotational speed, the Controller may trip into Fail condition, depending 
on how you configured the Controller (see Sections 

1.8

, 

1.9

 and 

3.13

).

Refer to the EXT pump instruction manual for the maximum allowable inlet pressure.

4.5

Operation with high pump temperature

Temperature sensors in the Controller and the EXT pump are monitored by the Controller. If the Controller detects 
that the pump temperature is too high, the power supplied to the pump-motor is reduced; the pump may not 
therefore be able to maintain full rotational speed if it is too hot.

If the pump speed falls to below 50% of its full rotational speed, the Controller may trip into Fail condition, depending 
on how you configured the Controller (see Sections 

1.8

, 

1.9

 and 

3.13

).

Refer to the EXT pump instruction manual for the pump operating temperature ranges.

Содержание EXC120























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды