manualshive.com logo in svg

Edwards EXC120, Инструкция по эксплуатации

Поделиться
Скачать
Edwards EXC120 Скачать руководство пользователя страница 39

© Edwards Limited 2008. All rights reserved. 

Page 31

Edwards and the Edwards logo are trademarks of Edwards Limited.

Installation

D396-14-880 Issue J

Figure 12 - Top cover of the Controller

3.13

Configure the Controller

3.13.1

Introduction

The Controller has four DIP switches which can be used to configure the Controller for your application. The DIP 
switches are on the top of the Controller (the CONFIG switches shown in 

Figure 12

). Set the DIP switches as described 

in the following sections.

3.13.2

Enable/disable the Internal Timer to monitor low pump speed 

Notes:

1.  If you pump a high gas load with the Internal Timer enabled (DIP switch 1 set to the off position), the 

EXT pump may stall before the Controller trips into Fail condition. Ensure that oil which backstreams 
from the backing pipeline will not adversely affect your process.

2. Disable the Internal Timer to provide the greatest protection against backstreaming when Fail condition 

occurs; as supplied, the Internal Timer is enabled.

Set DIP switch 1 to enable or disable the use of the Internal Timer when the pump rotational speed falls to below 50% 
of full rotational speed during operation (see 

Section 1.9.2

):

z

Set DIP switch 1 to 'on' to disable the timer.

 The Controller will then trip into Fail condition as soon as the 

pump rotational speed falls to below 50% of full rotational speed.

z

Set DIP switch 1 to 'off' to enable the timer.

 The Internal Timer will then start as soon as the pump 

rotational speed falls to below 50% of full rotational speed. If the pump speed remains below 50% of full 
rotational speed after the preset time, the Controller will trip into Fail condition.

Содержание EXC120























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды