Edwards E1M40 Скачать руководство пользователя страница 34

Страница: 34 / 64

A344-02-880 Issue J

Page 28

Edwards and the Edwards logo are trademarks of Edwards Limited.

Maintenance

5.5

Replace the fine oil-filter

Figure 9 - Fine oil-filter and gas-ballast bearing-plate locations

You must replace the fine oil-filter every time you change the oil in the pump. See

Figure 9

1. Isolate the pump from your electrical supply.

2. Place a suitable container underneath the oil drain scoop (5) below and to the left of the fine oil-filter (1). This

will contain any oil spill from the filter when it is unscrewed. The filter capacity is about 400 ml.

3. Unscrew the filter (direction arrows shown in

Figure 9

) using a suitable strap-wrench. Clean off any oil-spillage

on pump and filter housing surfaces. Dispose of the filter and any oil-spillage according to local environment
regulations covering industrial waste.

4. Make sure that the filter sealing ring (supplied with the new filter) is seated correctly on the new filter. Screw in

the new filter and tighten

turn using the strap-wrench.

AA/5007A

1. Fine oil-filter
2. Gas-ballast bearing-plate assembly
3. Gas-ballast inlets
4. Gas-ballast control
5. Oil drain-scoop

Содержание E1M40
























































Результаты поиска

Содержание E1M40

Отзывы:

Бренды по названию

Популярные бренды

Edwards E1M40, Инструкция по эксплуатации

Результаты поиска

Содержание E1M40

Отзывы:

Бренды по названию

Популярные бренды