Edwards B777-51-000 Скачать руководство пользователя страница 9

Страница: 9 / 40

Page 3

Edwards and the Edwards logo are trademarks of Edwards Limited.

Technical Data

B777-50-880 Issue D

Technical Data

2.1

General

2.2

Pumping media

CAUTION

Do not use an EXT556H pump to pump gases containing more than 20% oxygen unless a bearing purge is applied
as stated in

Section 2

. If so, the lubricant will be damaged and the pump will fail prematurely.

Note:

Concentrations of gases may be modified by the compression of the pump.

Table 1 - General information

General items

Reference data

Performance

See

Table 5

Dimensions and features

See

Figure 5

Maximum permitted external magnetic field

EXT556H DN160CF

3 mT horizontal, 5 mT vertical

EXT556H DN160ISO-K

2.5 mT horizontal, 5 mT vertical

EXT556HF ISO and CF variants

50 mT in any orientation

Installation category

EN61010 part 1, category 1

Pollution degree

CAN/CSA, UL, EN61010 part 1, category 2

Equipment type

Fixed equipment, for indoor use only

Operating altitude

up to 2000 m

Ambient operating temperature range

5 °C – 35 °C (air cooled)
5 °C – 40 °C (water cooled)

Relative humidity

10 – 90% non condensing

Electrical supply

80 V

Ambient storage temperature range

-30 °C - 70 °C

WARNING

Vent dangerous gases and gas mixtures safely. Do not expose people to these gases.

WARNING

Do not use EXT556H pumps to pump explosive gas mixtures as the pumps are not suitable for
this purpose.

WARNING

Do not use the EXT556H pump to pump mercury vapour, or allow mercury to come into contact
with the pump. If so, the rotor may corrode and fail.

Содержание B777-51-000




































Результаты поиска

Содержание B777-51-000

Отзывы:

Edwards B777-51-000, Инструкция по эксплуатации, Страница: 9 / 40

Результаты поиска

Содержание B777-51-000

Отзывы: