Edwards B777-51-000 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 40

Edwards B777-51-000 Скачать руководство пользователя страница 35

© Edwards Limited 2013. All rights reserved.

Page 29

Edwards and the Edwards logo are trademarks of Edwards Limited.

Service, spares and accessories

B777-50-880 Issue D

7

Service, spares and accessories

7.1

Introduction

Edwards products, spares and accessories are available from Edwards companies in Belgium, Brazil, China, France,
Germany, Israel, Italy, Japan, Korea, Singapore, United Kingdom, U.S.A and a world-wide network of distributors.
The majority of these centres employ Service Engineers who have undergone comprehensive Edwards training
courses.

Order spare parts and accessories from the nearest Edwards company or distributor. When ordering, state for each
part required:



Model and Item Number of the equipment



Serial number



Item Number and description of part

7.2

Service

Edwards products are supported by a worldwide network of Edwards Service Centres. Each Service Centre offers a
wide range of options including: equipment decontamination; service exchange; repair; rebuild and testing to factory
specifications. Equipment which has been serviced, repaired or rebuilt is returned with a full warranty.

The local Service Centre can also provide Edwards engineers to support on-site maintenance, service or repair of the
equipment. Please ensure that all accessories (i.e. water/air cooler) are removed prior to returning the pump for
service.

For more information about service options, contact the nearest Service Centre or other Edwards company.

7.3

Spares

7.3.1

ISX inlet-screen

An inlet screen is fitted to the pump as supplied to prevent damage from the entry of debris into the pump. The Item
Numbers of replacement inlet screens are given in

. There are two mesh sizes available: fine and coarse.

Select the mesh size appropriate to the requirements. The fine mesh (1 mm hole size) provides better protection
against falling objects e.g. fine pieces of filament, small grub screws. The coarse mesh (2 mm hole size) gives better
pumping performance. The coarse inlet screen is provided as standard.

7.3.2

Inlet-flange seals

EXT pumps are supplied with an inlet seal. The Item Numbers of replacement seals are given in

Table 9 - ISX inlet-screen

Flange size

Inlet-screen

Item Number

DN160ISO-K/DN160CF

Inlet screen (coarse)

B580-51-007

Inlet screen (fine)

B580-51-008

Table 10 - Inlet-flange seals

Inlet-flange

Inlet seal

Item Number

DN160ISO-K

ISO160 trapped 'O' ring, fluoroelastomer

B271-58-172

DN160CF

Copper compression gasket (pack of 5)

C083-00-003

«
...
33
34
35
36
37
...
»

Содержание B777-51-000









































Отзывы:

Нет отзывов