background image

4.  Installation

4.1  Safety

WARNING:

Obey the safety instructions in this section and take note of appropriate precautions.

Failure to observe these instructions may result in injury to people and damage to

equipment.

WARNING:

Do not expose any part of the human body to vacuum as it can cause injury.

WARNING:

The pump is not recommended for pumping explosive gases or hazardous

substances.

WARNING:

Use suitable lifting equipment to move the pump. The mass is approximately 48 kg.

WARNING:

Take care when moving the pump into position. The pump's weight makes it difficult

to slide and movement should only be attempted by two people.

A suitably trained and supervised technician must install the pump.

Ensure that the installation technician is familiar with the safety procedures that

relate to the products processed by the pump.

Wear the appropriate safety clothing when coming into contact with contaminated

components.

Dismantle and clean contaminated components inside a fume cupboard.

Vent and purge the vacuum system before starting installation work.

Disconnect other components in the pump from the electrical supply so that they

cannot be operated accidentally.

Refer to the Vacuum Pump and Vacuum System Safety manual (publication

number P40040100) before installing and using the pump to process hazardous or

flammable materials.

Safely route any electrical cables and pipes to prevent a trip hazard.

Check all required components are available and are of the correct type before

starting work.

Do not reuse O

rings or seals.

Page 16

A73001880_M - Installation

Содержание A73003983









































Отзывы: