EDWANZ group DEUTRONIC D-IBM2900 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 25

EDWANZ group DEUTRONIC D-IBM2900 Скачать руководство пользователя страница 10

Deutronic Elektronik GmbH
Deutronicstr. 5, D - 84166 Adlkofen
Tel.:    +49 8707 920-0
Fax:    +49 8707 1004
E-Mail:  sales@deutronic.com
http://www.deutronic.com

D-IBM2900

Stand: 08.03.2022

Seite 10 von 25

5.

Output device error (only 3AC)

CONEC plug 43-01001

An error evaluation of an external system can
only be carried out via a NO/NC relay contact
via a NO/NC relay contact

PIN ”1”: brown, center contact/ switching contact

PIN ”2”: white, normally open
PIN ”3”: blue, normally closed

PIN ”4”: black, not assigned

PIN ”5”: green/yellow, not assigned

Functionality Device Error:

From D-IBM2900 Gen3 on, the device are equipped with an error output in form of a
potential-free contact (NO/NC relays contact in the device). This can be used to implement
an error evaluation via an external system (e.g. PLC).

When all accumulators have reached the minimum voltage of approx. 58V, the NO contact
is closed. The relay is always supplied with voltage as soon as all accumulator modules are
in  a  functional  state  and  charged.  It  will  not  open  again  until  one  of  the  battery  voltages
drops below 51V, the battery is defective, or the cell temperature has risen above 70°C.
The fault activation occurs immediately (without any time delay) and is independent of the
supply  situation  of  the  device.  Thus,  even  before  the  power  supply  to  the  DBL  is
interrupted, the fault is detected and can be rectified.
The intelligent charging technology attempts to charge a defective battery, which no longer
has any internal voltage, up to 12 times with interruptions for approx. 10 sec. After that, no
further  charging  attempt  is  made.  This  causes  the  error  signal  to  be  interrupted  up  to  12
times  during  this  time,  but  then  to  be  evaluated  continuously.  After  an  overtemperature
error,  which  does  not  occur  during  normal  operation,  the  D-IBM  must  therefore  be
disconnected  from  the  mains  for  30  sec.  Disconnected  from  the  mains.  After  that  it  goes
back  to  normal  operation.  A  device  with  a  defective  battery  module  shows  the  behavior
after the mains connection that it clears the error 12 times for approx. 10 seconds, but then
remains continuously on fault.

«
...
8
9
10
11
12
...
»

Содержание DEUTRONIC D-IBM2900


























Отзывы:

Нет отзывов