manualshive.com logo in svg

EDT PCIe8g3 A5 10G, Руководство пользователя

Поделиться
Скачать
EDT PCIe8g3 A5 10G Скачать руководство пользователя страница 18

APPENDIX A: Registers for PCIe8g3 S5

Registers, UI

EDT, Inc.

2017 January 04

18

Registers, UI

0x00–0x7F Indirect

0x00 Command 

0x03 Interrupt Status 

0x04 Interrupt Enable 

Access / Notes:

8-bit read-write / PCD_CMD

Bit

 

Access

 

Name

 

Description

 

7–4

RW

PCD_STAT_INT_EN

Enables interrupts as defined in registers 

0x03 Interrupt Status

 and 

0x04 Interrupt Enable

.

3

RW

CMD_EN

Set this bit to enable the required DMA channels in 

0x10–11 DMA Channel Enable

 for DMA. When 

clear, resets all DMA channels, flushes all FIFOs, and clears all under- and overflow bits.

2–0

–

–

Reserved.

Access / Notes:

8-bit read-only / PCD_STAT

This register is connected to 1Hz test interrupt as an example of interrupts generated by the UI FPGA 
on the main board.

Bit

 

Access

 

Name

 

Description

 

7–4

R only

PCD_STAT_INT

Interrupt bits for the status bits.  If the corresponding bit is asserted in 

0x00 Command, 

then the 

corresponding bit of these four can be asserted to cause a PCI bus interrupt.

The PCI bus interrupt then is caused when the corresponding PCD_STAT signal [bits 3–0] is asserted. 
To reset the interrupt, disable and re-enable the appropriate PCD_STAT_INT_EN bit [7–4] in 

0x00 

Command

. 

3–0

R only

PCD_STAT

The state of user-definable STAT input signals as last sampled.

Access / Notes:

8-bit read-write / PCD_STAT_POLARITY

This register is connected to 1Hz test interrupt as an example of interrupts generated by the UI FPGA 
on the main board.

Bit

 

Access

 

Name

 

Description

 

7–5

–

–

Reserved.

4

RW

PCD_STAT_INT_ 
ENA

Provides global enable or disable for all interrupt bits [7–4] in 

0x03 Interrupt Status

 above, allowing the 

driver to disable and re-enable them in one operation without altering their states. A value of 1 enables 
the interrupts; a value of 0 disables them.

3–0

–

[no name]

Reserved.

Содержание PCIe8g3 A5 10G

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды