REF. 08751
EN
INSTRUCTION MANUAL
Operating Instructions
Before use
Remove any packing material and loose parts from unit.
Check the accessories before use. It should be fit with the
machine and your purpose. If the machine is new, the battery
must first be charged.
Attention! After long time storage, the battery capacity will
be reduce.
A new battery or one which has not been used for an
extended period achieves full performance only after
charging and discharging cycles. A substantial drop in
operating period per charge indicates that the battery is
worn out and must be replaced.
Battery charger (Fig.1)
The lithium-ion battery can be charged at any time and will
not develop a “memory” when charged after only a partial
discharge. It is not necessary to run down the battery pack
charge before recharging. Remove the battery pack from the
tool when convenient for you and your job. You can “top-off”
your battery pack’s charge before starting a big job or long
period of use.
Due to lithium-ion’s fade-free properties, the only time it is
necessary to charge the lithium-ion battery
pack is when the pack has reached the end of its charge. To
signal the end of charge, power to the tool will drop quickly.
Charge the battery pack as needed.
1. Charging the battery
This lithium-ion battery pack is shipped partially charged.
Before using it the first time, fully charge the battery pack. A
fully discharged battery pack with a temperature between
5°C and 40°Cwill charge in about 1 hour for 2.0Ah battery
pack.
l Plug the charger adapter into power source. The green light
on the charger stand will illuminate, indicating the charger is
powered.
l Slide the battery all the way into the charger stand. The
green light is off, and the red light on the charger stand will
illuminate, indicating that the battery is charging.
l The red light will go off after charging is complete and a
green light will appear.
NOTE:
Batteries may become warm while charging. This is
normal. If the battery is hot after continuous use in the tool,
allow it to cool down to room temperature before charging.
This will extend the life of your batteries.
WARNING: Always disconnect the battery pack from the tool
before any assembly, adjustments or changing accessories.
2. Insertion and removal of rechargeable battery (Fig.2)
Depress the battery-release button located on the front of
the battery pack to release battery pack. Pull the battery
pack out and remove it from the tool.
Warning!
Always remove the battery pack before making adjustments
to the equipment.
Be sure to read the following information before you put the
cordless equipment into operation: Charge the battery pack
with the charger. An empty battery pack requires a charging
period of approximately 0.5 to 1 hour for 2.0Ah battery pack.
Install the bits (Fig. 3)
When selecting a bit, use the right type for your job. For best
performance, always use sharp bits. To open the chuck jaws,
turning the sleeve in the counter clockwise direction.
Insert the bit deeply into the chuck, and then center the bit in
the chuck jaws.
To close the chuck jaws, turning the sleeve in the clockwise
direction as far as possible until the bit gets locked securely.
Torque adjustment (Fig. 4)
Select the desired operating torque by turning the ring to the
appropriate setting and adjust the drilling position simply.
Forward/Reverse adjustment (Fig 5)
The forward/reverse switch enables you to change the
rotation movement of the chuck, and also acts as a lock
button.
- For forward rotation, release trigger switch, and then
depress reverse switch to left handle side - For reverse
rotation, press switch to right hand side.
- The centre position locks the drill to off.
Always release the trigger switch when changing rotation.
Note the first time you use the drill after changing rotation,
you may hear a click when the drill is turned on, and this is
normal and does not indicate a problem.
WARNING:
Never change the forward/reverse switch while
the drill is rotating as this damage the drill.
Speed gear box (Fig. 6)
Two speed ranges can be pre-selected with the gear selector.
Gear I: Low speed range: for screw driving or working with
large drilling diameter.
Gear II: High speed range: for working with small drilling
diameter.
LED light (Fig. 7)
A LED light source is integrated in the housing.
The light is activated as soon as the On/Off switch is pressed.
Fully automatic spindle locking (Auto-lock)
When the trigger switch is not pressed, the drill spindle and
Drill / Driver
