Edinburgh Sensors GasCheck Скачать руководство пользователя страница 23

 

GasCheck 

 

Operating Manual V2.4 

 

18 

7. 

WARRANTY 

Edinburgh Instruments Ltd. guarantees the equipment against defective materials or 
workmanship for a period of one year from the date of the delivery. In no event shall the 
Company be liable for any consequential loss or damage arising from failure of the 
equipment under warranty. 

At  the  end  of  the  one-year  period,  all  claims  upon  and  all  liability  from  failure  of  the 
equipment shall be absolutely at an end. 

No warranty is made or implied as to the suitability of any equipment for  the Purchaser’s 
intended use beyond such performance specifications. 

The Purchaser warrants 

That they will carefully examine and list all parts of the equipment supplied by Edinburgh 
Instruments Ltd. and notify Edinburgh Instruments Ltd. in writing of any  shortage, defect 
or  failure  to  comply  with  the  contract,  which  is  or  ought  to  be  apparent  upon  such 
examination and test, within 48 hours of the equipment being delivered to or collected by 
the Purchaser. 

That  the  equipment  will  be  operated  in  accordance  with  the  instructions  and  advice 
detailed  in  the  appropriate  operating  instruction  manual,  or  any  other  instructions  which 
may be provided by Edinburgh Instruments Ltd.  Edinburgh Instruments Ltd. shall not be 
held responsible for any defect arising from the Purchaser’s failure to comply with these 
recommendations and instructions or from damage arising from negligence or exposure to 
adverse environmental conditions. 

The warranty is effective only if:- 

The  equipment  has  been  paid  for  in  accordance  with  the  normal  payment  terms  and 
conditions. 

Any  defects  in  the  equipment  supplied  are  notified  immediately  by  the  Purchaser  to 
Edinburgh Instruments Ltd. 

The  equipment  is  returned  to  Edinburgh  Instruments  Ltd.  at  its  Livingston  premises, 
transportation  and  insurance  prepaid,  and  undamaged by the failure to provide sufficient 
packaging. 

The warranty covers:- 

Engineer costs to inspect and repair. 

Materials or components, that require to be replaced. 

Return carriage costs to the Purchaser. 

The  timing  of  the  inspection  and  repair  of  the  equipment  will  be  determined  entirely  at 
the discretion of Edinburgh Instruments Ltd. 

Содержание GasCheck



























Отзывы: