EdilKamin WINDO3 50 Скачать руководство пользователя страница 18

Страница: 18 / 24

ENGLISH

Lighting a cold fireplace

1. Check the existing ash bed is not too high. If the

1. Check the existing ash bed is not too high. If the
ash bed is too high, there is a danger of opening the

ash bed is too high, there is a danger of opening the
door of the fireplace to add wood and possible brazier

door of the fireplace to add wood and possible brazier
fragments fall out of the fireplace.

fragments fall out of the fireplace.
2. Position the adjustment lever of the valve in the “total

2. Position the adjustment lever of the valve in the “total
opening” position . The air for combustion will flow

opening” position . The air for combustion will flow
intensely to the wood in the fireplace, to quickly reach

intensely to the wood in the fireplace, to quickly reach
good combustion.

good combustion.
3. place the wood in the fireplace without excessively

3. place the wood in the fireplace without excessively
squashing it in. Position a firelighter between the wood

squashing it in. Position a firelighter between the wood
logs and light. Never user materials such as petrol,

logs and light. Never user materials such as petrol,
alcohol and similar to switch on.

alcohol and similar to switch on.
4. At this point, close the door and monitor it for a few

4. At this point, close the door and monitor it for a few
minutes. If the fire should extinguish, slowly open the

minutes. If the fire should extinguish, slowly open the
door, re-position another firelighter between the logs

door, re-position another firelighter between the logs
and light again.

and light again.

Lighting a hot fireplace

When should wood be added? When the fuel is almost

When should wood be added? When the fuel is almost
completely consumed to embers. With the glove,

completely consumed to embers. With the glove,
slowly open (to avoid formation of vortexes that can

slowly open (to avoid formation of vortexes that can
cause smoke to exit) the door. Add the desired wood to

cause smoke to exit) the door. Add the desired wood to
the fireplace, locating it on the existing embers (within

the fireplace, locating it on the existing embers (within
the quality limits indicated in the technical table).

the quality limits indicated in the technical table).
Product functioning changes with the chimney flue

Product functioning changes with the chimney flue
draft and adjustment of the air valve in combustion.

draft and adjustment of the air valve in combustion.

Functioning with initial low draft

To extract air for combustion and discharge the

To extract air for combustion and discharge the
smoke, the fireplace needs a draft to be exerted on the

smoke, the fireplace needs a draft to be exerted on the
chimney flue.

chimney flue.
If the draft is weak, initially light a “starter” fire using

If the draft is weak, initially light a “starter” fire using
small sized lighting material.

small sized lighting material.
Once the correct draft is restored, you can add the fuel.

Once the correct draft is restored, you can add the fuel.

As with all the products, the wood product heats and

As with all the products, the wood product heats and
cools during the various phases. This would lead to

cools during the various phases. This would lead to
normal dilation. Such dilation can cause slight settling

normal dilation. Such dilation can cause slight settling
noise, which is not a reason for dispute.

noise, which is not a reason for dispute.

INSTRUCTIONS FOR USE

FUEL

The product was designed to burn wooden logs or
sawdust briquettes.
Use dry wood logs (max. humidity 20%)Use logs The
use of damp wood would cause the product and the
flue to get dirty, the risk of smoke and a lower yield
than that declared.Each type of wood has different
characteristics that also influence combustion yield.
The data outlined on this manual are with wood used
during certification.
In general wood can have a heat of combustion up to
4.5 kWh/kg while cut fresh it has heat of combustion
around 2 kWh/kg
In general, beech or elm is recommended, or however
class A1 wood according to UNI EN ISO 17225-5
Attention to prolonged use of wood with aromatic oils
(e.g. eucalyptus). Cast iron parts can deteriorate
Use the recommended quantities of wood:
Overloading causes overheating, resulting in damage:
• possible deformation of the inner parts;
• possible irreversible changes to the colour of the

paint on the metal parts for which Edilkamin or the
retailer cannot be held liable.

To respect the environment and safety, do NOT burn,
among other things: plastic, varnished wood, coal and
bark waste. Do not use the product as an incinerator.
Use of these fuels also nullifies the guarantee.

First switch on phases

• Ensure you have read and understood the content

of this manual

•

• Remove all the inflammable parts from the product

Remove all the inflammable parts from the product
(manuals, labels, etc.). In particular remove any

(manuals, labels, etc.). In particular remove any
labels from the glass. If they melt, they would

labels from the glass. If they melt, they would
irreversibly damage the glass.

irreversibly damage the glass.

For initial switch on of the fireplace, always use the

For initial switch on of the fireplace, always use the
smallest logs. Use larger wooden logs to raise the fire.

smallest logs. Use larger wooden logs to raise the fire.
Always locate the wood deep in the fireplace.

Always locate the wood deep in the fireplace.
There may be a slight smell of paint the first few times it
is ignited, however, this will disappear quickly.