background image

 

Page 10 of 10 

The web page configurations for the various 6400LF2 deployments are shown below.  The two darker-
shaded rows indicate the 

minimum

 configuration required for each deployment. 

6400LF2  
GUI Configuration 
Page 

6400LF2 as 
Gateway 
Router  

6400LF2 within existing 
infrastructure 

6400LF2 behind an 
existing firewall 

Network 

Yes 

Yes 

Yes 

VoIP/ALG  

Yes 

Yes 

Yes 

NAT 

Yes 

Optional 

Yes 

Firewall 

Yes 

Optional, but 
recommended 

Optional, but 
recommended 

DHCP 

Yes 

Yes (but should be 
disabled if DHCP server 
already exists) 

Yes (but should be 
disabled if DHCP server 
already exists) 

Traffic Shaper 

Yes 

Yes 

Optional (depends on 
network topology) 

Traffic Simulator 

Only for 
testing 

Only for testing 

Only for testing 

System 

As needed 

As needed 

As needed 

 

Please visit our website at 

www.edgewaternetworks.com

 or contact the Edgewater Technical 

Assistance Center at 408.351.7255 for additional information or assistance. 
 

  

 

Edgewater Networks, Inc.

  

2895 Northwestern Parkway 
Santa Clara, CA 95051 
Phone: (408) 351-7200 
[email protected] 
 

Copyright© 2008, Edgewater Networks, Inc.

  All rights reserved.

 

 

Converged Networking. Simplified. 

Содержание EdgeMarc 6400LF2











Отзывы: