Edgetech 6205S2 Скачать руководство пользователя страница 8

Страница: 8 / 108

viii

6205s2 BATHYMETRIC AND SIDE SCAN SONAR

0025262_REV_A

RETURNED MATERIAL AUTHORIZATION

Prior to returning any equipment to EdgeTech, a Returned Material Authorization (RMA) Number must

be obtained from

USTOMER

ERVICE

RMA Purpose

The RMA Number identifies returned equipment when it arrives at our receiving dock and enables tracking

while at our facility. Refer to the RMA number on all documentation and correspondences.
All returned materials must be shipped prepaid. Freight collect shipments will not be accepted. All

equipment should be adequately insured for shipping, but equipment belonging to EdgeTech must be

insured for full value.
If there is more than one item per consignment, include a packing with the shipment. An invoice can

double as a packing slip only when the contents are clearly numbered and identified on the invoice.

CAUTION!

Never attempt to ship a topside unit in its SKB® case alone.

Although rugged, these cases are not intended to be used as shipping

containers, and the delicate internal components could be damaged.

Shipping in this manner will void any warranties.

NOTE:

All shipping charges shall be the customer's responsibility, unless

under warranty, as EdgeTech will pay for return shipping.

NOTE:

For International Shipments valued over $1000, the following

Shipper's oath must be sent with the invoice.

Shipper's Oath:

"I, ______________________________, declare that the articles herein specified are the growth,

produce, or manufacture of the United States; that they were exported from the

United States from the port of _____________________, on or about _______________; that they

are returned without having been advanced in value or improved in condition by any

process of manufacture or any other means; and that no drawback, or allowance has

been paid or admitted hereof."
Signed ______________________________

Содержание 6205S2













































































































Результаты поиска

Содержание 6205S2

Отзывы:

Похожие инструкции для 6205S2

Бренды по названию

Популярные бренды

Edgetech 6205S2, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S2

Отзывы:

Похожие инструкции для 6205S2

Бренды по названию

Популярные бренды