Edgetech 6205S Скачать руководство пользователя страница 43

Страница: 43 / 97

4-26

6205s BATHYMETRIC AND SIDE SCAN SONAR

0020300_REV_E

4.2.2

Serial Port Connections

There are three RS-232 serial ports provided on the 6205s Sonar Interface box. COM1 and COM2 have

been configured for high speed and high accuracy). COM3 is configured for standard RS-232 serial

connections. Typical latencies for the high speed/high accuracy ports are less than 100us, whereas the

standard serial port has up to 100ms.
These serial ports are provided to intake the navigation, heading, and attitude (roll, pitch, and heave) data

from the supporting sensors. The

CONFIGURING

COM

PORTS

section of this manual has instructions on

how to configure them.
If the Rack Mount topside is being utilized, it can serve as a splitter for serial data. The output ports pair

with the serial ports located directly above them. These ports are unidirectional.

4.2.3

Hardware Connectivity

IGURE

4-1

is a block diagram that illustrates interconnections between the 6205s Swath Bathymetry and

Dual Frequency Side Scan Sonar Head, the 6205s-R Rack Mount Topside Interface, and all supporting

sensors. This illustration gives examples of three possible sensor configurations that are explained below.

Figure 4-1: 6205s Rack Mount Topside Interface Connections

Note:

The 6205s-P portable topside interface connections are similar.

Heading,

Position, Time

Attitude, Heading,

Position, Time

Heading

Roll/Pitch/Heave

Position

1PPS

6205s Sonar Head

IP Address: 192.9.0.101

Example 1

Attitude

Not Used

Example 2

Example 3

Power

115/220 VAC

Not Used

Topside Computer

IP Address 192.9.0.99

Содержание 6205S


































































































Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды

Edgetech 6205S, Руководство пользователя по оборудованию

Результаты поиска

Содержание 6205S

Отзывы:

Похожие инструкции для 6205S

Бренды по названию

Популярные бренды