EdgeStar TWR325ESS Скачать руководство пользователя страница 4

General Safety 

  Always unplug an appliance from the power supply before attempting any service. Disconnect the 

power cord by grasping the plug, not the cord. 

  Do not allow children or pets to play on or in the appliance.  

  This machine is not intended for use by persons (including children) with reduced physical, sensory or 

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or 
instruction concerning use of the machine by a person responsible for their safety. 

  Do not install or store this appliance where it will be exposed to the weather. 

  Disconnect from the power socket before cleaning or maintenance.  

  If the plug (power cord) is damaged, it must be replaced by the manufacturer or an authorized service 

representative. 

  This machine shall be repaired only by an authorized service representative. Only genuine 

replacement parts should be used. 

  If connected to a circuit protected by fuses, use time-delay fuses with this appliance. 

  Do not lean items against the glass door. 

  Please do not close the door with excessive force. If it is found difficult to close the door, please check 

for obstruction. 

  When you plan to dispose of this unit in the future, please comply with the local waste disposal 

regulations. Remove the door so that children and pets will not be trapped in the unit. 

 

 

Содержание TWR325ESS























Отзывы: