manualshive.com logo in svg

Edge MTP Tap Module, Установка и испытание, Страница: 12 / 13

Поделиться
Скачать
Edge MTP Tap Module Скачать руководство пользователя страница 12

Standard Recommended Procedure 003-128 | Issue 4 | September 2018 | Page 12 of 13

10.  Simultaneous Testing of the Live and Tap Portions of an MTP 

Tap Module 

10 .1

 

This section describes how to test the entire system at once with one source and two meters. This is 

an alternative way to test compared to Steps 8 and 9. Note that this can only be done if all the permanent 

harnesses are installed or test harnesses are purchased to mimic the harnesses that will be installed. Also, three 

craft persons will be needed instead of two.  

10 .2

 

To calculate the system losses for the system use the values calculated above in Steps 8 and 9 and 

reference the test equipment as shown in Step 7. 

10 .3

 

To begin testing the system (Figure 16):

Step 1: 

Install the 

Light Source/RJ1 LC connector

 into the number 2 port of the Edge module, Module “B”. 

Step 2: 

Install 

Meter 1/RJ2’s LC connector adapter

 onto LC number 1 of the harness plugged into the front-

mounted LIVE Port of the MTP Tap module.

Step 3: 

Install 

Meter 2/RJ3’s LC connector adapter

 onto LC number 2 of the harness plugged into the TAP port 

of the MTP Tap module.

Step 4: 

Continue testing through on the even fibers of the EDGE module, Module “B,” using Tables 3 and 5 for 

testing sequences.

Figure 16

LIVE

LIVE

TAP

Module harness

TAP port 

test harness

          

         

          

         M1

    

RJ2 

    and 

    adapter

    

RJ3 

    and 

    adapter

          

         

RJ1

   

Do NOT 

    disconnect

   

Do NOT 

    disconnect

0.00 dB

Pretium EDGE

  Module “B”

B

2

3

B

1

2
1

A

TPA-6140

multimode only

  Light 

 Source

     

“Near end”

“Far end”

B

6

12
11

A

B

5

10

9 

A

B

4

8
7

A

B

3

6

PnP

 Module

Part Number

Serial

MADE IN MEXICO

5

A

B

2

4
3

A

B

1

2
1

A

   W

AR

R

AN

TY

VOID

 MTP Tap Module “A”

 “A”

Note:  Fiber loss

depends on length

 of system

 LC  #12

 LC  #1

          

         

          

         M2

   

Do NOT 

    disconnect

0.00 dB

 LC  #2

Содержание MTP Tap Module














Отзывы:

Нет отзывов