
Terminals and Controls ED7400
5. Low Pass Crossover Control
The control is used to select the low pass filter frequency. The frequency ranges are from 45
Hz to 300 Hz.
6. Crossover Control Switch
This switch is used to select high pass, low pass or flat (no crossover) operation for the
amplifier speaker outputs.
7. High Pass Crossover Control
The control is used to select the High pass filter frequency. The frequency ranges are from 45
Hz to 300Hz.
8. Bass Boost Remote Input Jack
Use to plug in the remote bass controller. (Optional ) see back
9. High Level Input
To be used when no RCA’s are available. Use the provided loom to connect to closest
speakers. The loom connector will only fit one way around. Once plugged in you should
connect the wires as below:
Left Positive - White Right Positive - Grey Left Negative - White / Black
Right Negative - Grey / Black
10. Indicator LED
When the amplifier is operating correctly the LED will show as green. When the amplifier is in
protection mode the LED will show as red.
11. Power Connections
Power connections. See Connections section for details on correct connections.
12. Fuses
Please ensure the following fuse rating is used when replacing fuses: 15 amp x 2
13. Speaker Terminal Output
For connection to the speakers. See Application section for wiring examples.
P o w e r
P r o t e c t
S P -
S P -
S P +
S P +
R
I n p u t
L +
R +
L -
R -
R
L
L
H i L e v e l
L i n e O u t
L i n e I n
O F F
O N
S u b s o n i c
P h a s e
L P F
G a i n
M i n M a x 3 5 H z 2 5 0 H z 0 ° 1 8 0 °
8 0 H z
1 6 H z
2 4 d B
0 d B
R e m o t e
B a s s
B o o s t
ED72500
ED71200
ED71200
ED7800
ED7800
ED72500
MONOBLOCK AMPLIFIER 1 X 1250 WATTS RMS
ED71600
ED71600
4 CHANNEL AMPLIFIER 4 X 200 WATTS RMS
ED7400
ED7400
2 CHANNEL AMPLIFIER 2 X 100 WATTS RMS
MONOBLOCK AMPLIFIER 1 X 600 WATTS RMS
4 CHANNEL AMPLIFIER 4 X 100 WATTS RMS
4 x 35 AMP
3 x 35 AMP
INPUT
2 x 15 AMP
2 x 25 AMP
2 x 20 AMP
1
2
5
7
8
3
4
6
9
10
11
12
13
1
2
3
5
7
8
6
4
9
10
11
12
1
2
3
4
9
5
6
7
14
8
10
11
12
13
1
1
2
3
4
5
6
8
9
10
11
12
13
7
2
3
4
5
6
7
8
9
10
11
12
13
14
1. Low Level Output
A daisy chain output For connection to another amplifier with a low level input using only a
single RCA output from the source (headunit).
2. Low Level Input
For connection to any source (headunit) with a low level output. This is your RCA output from
the source (headunit)
3. Gain Control
Used to match the input signal of the source to the amplifier. See the setup section for more
details.
4. Bass Boost Switch
To provide up to an extra +12 dB of bass boost at 45 Hz. Use this boost to increase bass output
from the amplifier.
Содержание ED71200
Страница 1: ...AMPLIFIER ...
Страница 12: ......