Edco GMS-14 Скачать руководство пользователя страница 15

Страница: 15 / 16

Printed in USA

Page 15

E-MS-GMS14&20-I-1002

100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA

Phone (301) 663-1600 • 1-800-638-3326

Fax (301) 663-1607 • 1-800-447-3326

Website: www.edcoinc.com • Email: [email protected]

Repairs are to be preformed
by EDCO or by approved
EDCO repair technicians.

Read and follow all instructions
in the Engine Manufacturer’s
Owner’s Manual.

Maintenance Schedule

Change Engine Oil*

Daily

Before

Operation

Every 4 Hours

As Required

Every 50 Hours

of Operation

Visually Inspect Entire

Machine and Hardware

Clean Air Filter Element*

Inspect Guards

Check Engine Oil*

Inspect Blade and

Arbor Shaft

Lubricate Wheels

on Rolling Table

Inspect Belts

Clean Dust and

Dirt Off Machine

Replace Spark Plug*

Annually

*Gasoline Models Only

1234567890123456789012345678901

Belt Tensioning

Clean Water Strainer

Grease Bearings

123456789012345678901234567890

Before each

Operation

Daily

Every 4 HoursEvery 50 Hours

of Operation

As Required

Annually

Содержание GMS-14

















Результаты поиска

Содержание GMS-14

Отзывы:

Edco GMS-14, Инструкция по эксплуатации, Страница: 15 / 16

Результаты поиска

Содержание GMS-14

Отзывы: