Edco GMS-10 Скачать руководство пользователя страница 10

Printed in USA

© 2000

Page 10

E-GMS10-I-03/00

100 Thomas Johnson Drive, Frederick, MD 21702-4600 USA
Phone (301) 663-1600 • 1-800-638-3326
Fax (301) 663-1607 • 1-800-447-3326
Website: www.edcoinc.com • Email: [email protected]

Change Engine Oil:

Check Engine Oil before each operation. Open the filler cap and look at the dip stick. (

Figure 16

)

Oil should be clearly visable both on the stick and in the cavity and should look fairly clean. Running the machine on
dirty oil or when the oil is low will result in damage to the equipment.

Change the Engine Oil after every 50 hours of operation - or sooner as conditions require.  Refer to the Engine
Manufacturer’s Owner’s Manual for specific viscosity recommendations and changing instructions.

Inspect and Clean Oil Air Filter:

Shown with Honda Cyclone Dual Filter style element.

Outer foam filter is removable for cleaning.

Refer to the Engine Manufacturer’s Owner’s Manual

for instructions on specific models.

Check air filter at least once daily.

(Figure 19)

Dirt build up on the filter will cause the engine to wear out faster.

Figure 18

Figure 16

Figure 19

Figure 17

Oil Drain

Dip Stick/

Filler Cap

Содержание GMS-10













Отзывы: