ECS P5SD-B Plus Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 36

ECS P5SD-B Plus Скачать руководство пользователя страница 23

20

Power Management

Default: User Define

This item acts like a master switch for the power-saving modes and hard disk timeouts. If
this item is set to Disabled, all the power-saving modes are disabled. If this item is set to
Max Saving, doze, standby, and suspend mode, will occur after a timeout of 20 seconds. If
this item is set to Min Saving, doze, standby, and suspend mode will occur after a timeout
of 40 minutes. If the item is set to User Define, you can insert your own timeouts for the
power-saving modes.

PM Control by APM

Default: Yes

Windows 95 and 98 have built-in power management capabilities called APM (advanced
power management). When you enable this item, you allow the APM routines in Windows
to operate on your system.

Video Off Option

Default: Suspend -> Off

This option defines which level of power-saving mode is required in order to power down
the video display. As a default, the video powers down in both suspend mode and standby
mode.

Video Off Method

Default: DPMS Support

This item defines how the video is powered down to save power. As a default, this is set to
DPMS Support (display power management software).

Modem Use IRQ

Default: 3

If you would like an incoming call on a modem to automatically resume the system from
suspend mode, use this item to specify the interrupt request line (IRQ) that is used by the
modem.

Soft-Off by PWRBTN

Default: Delay 4 sec

Under ACPI (advanced configuration and power interface) the system can be turned off
mechanically (by the power button) or it can undergo a software power off. If the system
has been turned off by software, the system can be resumed by a LAN, MODEM or
ALARM wake up signal. This item allows you to define a software power off using the
power button. If the value is set to Instant-Off, the power button will automatically cause a

«
...
21
22
23
24
25
...
»

Содержание P5SD-B Plus





































Отзывы:

Нет отзывов