ECS 651-M Скачать руководство пользователя страница 61

Страница: 61 / 75

SIS OnChip PCI Device

Scroll to this item and press <Enter> to view the following screen:

Phoenix – AwardBIOS CMOS Setup Utility

SIS OnChip PCI Device

Item Help

SIS-7012

AC97Audio

[Enabled]

SIS-7013 S/W Modem

[Enabled]

SIS 10/100M Ethernet

[Enabled]

Onboard LAN Boot ROM

[Disabled]

System Share Memory Size

[32 MB]

Menu Level

↑

↓

→

←

: Move

Enter : Select

+/-/PU/PD:Value:

F10: Save ESC: Exit F1:General Help

F5:Previous

Values

F6:Fail-Safe

Defaults F7:Optimized

Defaults

SIS-7012 AC97 AUDIO (Enabled)

Enables and disables the onboard AC 97 audio function. Disable this item if
you are going to install a PCI audio add-on card.

SIS-7013 S/W Modem (Enabled)

Enables and disables the onboard modem. Disable this item if you are going
to install an external modem.

SIS 10/100M Ethernet (Enabled)

Enables and disables the onboard LAN.

Onboard LAN Boot ROM (Disabled)

Use this item to enable and disable the booting from the onboard LAN or a
network add-in card with a remote boot ROM installed.

System Share Memory Size (32MB)

This motherboard has a built-in graphics system that uses UMA (Unified
Memory Architecture) so that the graphics reserves a part of main memory for
video memory. Use this item to determine how much of the main memory can
be used as video memory.

Press <Esc> to return to the Integrated Peripherals screen.

Содержание 651-M












































































Результаты поиска

Содержание 651-M

Отзывы:

Похожие инструкции для 651-M

Бренды по названию

Популярные бренды

ECS 651-M, Руководство пользователя

Результаты поиска

Содержание 651-M

Отзывы:

Похожие инструкции для 651-M

Бренды по названию

Популярные бренды