ECR International Utica Boilers UCS-380 Скачать руководство пользователя

Страница: 68 / 88

13 - TROUBLE SHOOTING

13.1 Troubleshooting

This boiler is fitted with an electronic regulation and control

unit.
Control system is a microprocessor, Comfort Master©, which

controls and protects the boiler. If a fault is detected anywhere

in the boiler, boiler will lock out and display will show the fault

code as follows:

Red flashing display:

• The

symbol

•

The "

RESET"

symbol

Descriptions of each error code are given in the table below.

To reset an error code, press

button for 2 seconds.

If the error code continues to display, search for the cause in

error table and follow instructions given in solution section.

Error Code Table

Error

Code

Description

Probable Causes

Checking/Solution

E00

Storage unit PSU parameter

not found

Bad connection

Check the wiring

E01

The safety parameters are

incorrect

Bad connection

PSU defective

Check the wiring

Replace PSU

E02

Supply temperature sensor

short circuited

Bad connection

Sensor fault

Sensor not/poorly connected

Check the wiring

Check sensors are operating correctly

Check sensor has been correctly fitted

Replace sensor if necessary

(CHART 1)

E03

Supply temperature sensor

open circuit

Bad connection

Sensor fault

Sensor not/poorly connected

Check the wiring

Check sensors are operating correctly

Check sensor has been correctly fitted

Replace sensor if necessary

(CHART 1)

E04

E05

Temperature of heat

exchanger too low.
Heat exchanger

temperature too high

Bad connection

Sensor fault

Sensor not/poorly connected

No circulation

Check the wiring

Replace sensor if necessary

Purge air in heating system

Check for water circulation (direction, pump, valves)

Check water pressure

Check sensors are operating correctly

Check sensors have been correctly fitted

Check cleanliness of heat exchanger

(CHART 1

E06

Return temperature sensor

short circuited

Bad connection

Sensor fault

Sensor not /poorly connected

Check the wiring

Check sensor has been correctly fitted

Check sensors are operating correctly

(CHART 1)

E07

Return temperature sensor

open circuit

Bad connection

Sensor fault

Sensor not /poorly connected

Check the wiring

Check sensor has been correctly fitted

Check sensors are operating correctly

(CHART 1

E08

E09

Return temperature too low

Return temperature too

high

Bad connection

Sensor fault

Sensor not/poorly connected

No circulation

Check the wiring

Replace sensor if necessary

Purge air from heating system

Check for water circulation (direction, pump, valves)

Check water pressure

Check sensors are operating correctly

Check sensors have been correctly fitted

Check cleanliness of heat exchanger

(CHART 1)

Note corresponding

troubleshooting charts for further

information (CHART xxx)

PN 240011662 Rev. H [04/30/2019]

Содержание Utica Boilers UCS-380

























































































Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды

ECR International Utica Boilers UCS-380, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Utica Boilers UCS-380

Отзывы:

Похожие инструкции для Utica Boilers UCS-380

Бренды по названию

Популярные бренды