background image

 

08.10.2018 Rev. 04 

 

 
2.

 

TERMS OF WARRANTY 

 

Main and auxiliary equipment and all components used in Ecostar gas burners are guaranteed  

for  1  year  by  TERMO  ISI  S

İ

ST.  A.

Ş

  starting  from  the  date  of  commissioning  under  the  maintenance, 

adjustment, operating conditions and relevant mechanic, chemical and thermal effects explained herein. 
 

 
Please note that this warranty is only valid if the device(s) is commissioned and maintained by our 
authorized services. 

 

 
Our  company  reserves  the  right  to  make  any  modifications  on  the  product  and  all  instructions 
thereof for improvement purposes.  

 
 
 

2.1.

 

Out of Warranty Conditions 

 

 

Any  damage  arising  out  of  or  in  relation  to  customers’  non-compliance  to  their  responsibilities 

with regards to installation, commissioning, operation and maintenance, 

 

Any damage arising out of or in relation to commissioning, repairs and maintenance carried out by 

unauthorized services,

 

 

Any damage that may occur during transportation or storage of the product,

 

 

Not preserving the product in its original packaging until the installation stage, 

 

Incorrect  and  poor  electrical  connections,  failures  due  to  incorrect  voltage  applications,  frequent 

repetition of voltage fluctuations, 

 

Any  damage  that  may  occur  as  a  result  of  incorrect  fuel  usage  or,  foreign  substances  in  the  fuel 

used or using of the product without any fuel,

 

 

Any  damage  that  may  occur  due  to  foreign  particles  entered  into  the  product  during  installation 

and operation, 

 

Failures due to incorrect device selection,

 

 

Any damage to unit due to natural disasters,

 

 

Devices without any warranty certificates,

 

 

Warranty Certificates without the stamp and signature of the authorized dealer or service,

 

 

Devices with any falsification on the warranty certificate or without an original serial number. 

 

 

The  risks  during  transportation  of  device  under  the  responsibility  of  customer  belong  to  the 

customer.

 

 

Presence of misuse faults are indicated in the reports issued by authorized service stations or our 

authorized  agent,  dealer,  representative  or  our  factory  in  case  of  unavailability  of  authorized 
service stations.

 

 

Customers  may  apply  consumer  protection  arbitrator  committee  with  regards  to  this  report  and 

request for an expert report.

 

 
 
 
 

Содержание GRM 15
































Отзывы: