Specifications
Living Water II
Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/2 gallon/minute (2 Liters/minute)
Min. Operating Pressure. . . . . . . . . . . . . . . . . . . . 15 psi (105kPa)
Max. Operating Pressure . . . . . . . . . . . . . . . . . . . 100 psi (609kPa)
Water Temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 – 100 F (5 – 38 C)
Electrical Requirements . . . . . . . . . . . . . . . . . . . . 20 watts, 50 – 60 Hz, 110 or 230 volts
Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Activated Carbon Block with lead
Adsorbent media
Particulate Reduction . . . . . . . . . . . . . . . . . . . . . . 0.5 micron nominal
Filter Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 year or 1000 gallons (4,000 Liters)
Chemical Additives . . . . . . . . . . . . . . . . . . . . . . . . None
UV Lamp Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10,000+ on/off cycles (approx. 2 years)
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.5 x 13 x 4 in. (19 x 33 x 10 cm)
Dry Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 lbs. (2.75 kg)
Living Water III
Same as above except
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 x 13 x 4 in. (28 x 33 x 10 cm)
Dry Weight. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 lbs. (3.65 kg)
This Class B system conforms to NSF/ANSI 55 for the supplemental bactericidal
treatment of disinfected public drinking water or other drinking water which has
been tested and deemed acceptable for human consumption by the state or local
health agency having jurisdiction. The system is only designed to reduce normally
occurring non-pathogenic microorganisms. Class B systems are not intended for
disinfection of contaminated water.
System conforms to NSF/ANSI 42 for the specific performance claims as verified and
substantiated by test data.
Changing the UV Lamp
It is recommended that you contact your authorized Living Water distributor to replace
the UV lamp when it is no longer working, or every two years.
WARNING: To prevent electrical shock, unplug the power supply from the electrical
outlet. DO NOT PROCEED BEFORE MAKING SURE THERE IS NO ELECTRICITY
GOING TO THE SYSTEM.
1. Disconnect the tubing from the top and bottom of the system. Remove the unit from
the wall mounts if applicable. Lay the system down horizontally.
2. Using a Phillips head screwdriver, remove the four (LWII) or six (LWIII) screws located
on the bottom of the unit.
3. Slide the bottom cup off the unit.
4. Remove the screw (A) and the retainer wire (B)
5. Disconnect the two wire connectors (C) and (D) coming
from the lamp and gently slide the lamp out of the system.
6. Carefully slide the replacement UV lamp into the system
holding it by the ceramic base only. Reconnect the two wire connectors (C) and (D).
NOTE: Touching the glass portion of the bulb will leave an oil deposit and may cause
the bulb to fail prematurely. If you should inadvertently touch the glass, clean the
entire bulb surface using denatured alcohol before installing.
7. Reinstall the retainer wire (B) back into its original position and tighten screw (A).
8. Replace the bottom cup and secure with screws.
9. Remount the system, reconnect the tubing and plug in the power adapter.
If the lamp does not illuminate, contact your authorized EcoQuest Business Owner.
Do not use the system until the lamp is functioning properly. If you do not have an
EcoQuest Business Owner, contact EcoQuest directly at 800.989.2299.
A
B
C
D
5
6
