PN PIRZB1-ECO R1.00 Rev date 6/26/2017
Problem
Solution
Attempt to pair the sensor is unsuccessful.
Reset the detector to default mode and then set to
pairing mode (see section 3.5).
The sensor and the Touchscreen (control panel)
do not communicate.
Perform the signal strength testing procedure
described in the control panel installation manual.
Make sure that the signal is sufficient. If necessary,
replace the sensor
’s battery.
The sensor sends a Low Battery indication.
To ensure continuous proper operation, replace the
battery within two weeks of the first Low Battery
indication.
Panel does not arm because of an unrecognized
sensor malfunction.
Consult with your installer or system provider before
you disable a zone. Disable the sensor zone (see
the control panel user manual). Note that disabling
a sensor zone lowers the overall security level of
your system.
4. TROUBLESHOOTING
If you encounter one of the following problems with the PIRZB1-ECO, use the following solutions to
resolve the problem:
PIRZB1-ECO
Wireless Digital Pet Resistant PIR Detector
3
rd
Party Certifications: FCC, IC, ETL, ZigBee HA, iControl
Installation Instructions
1. INTRODUCTION
The PIRZB1-ECO pet resistant detector is a
microprocessor-controlled wireless digital PIR
detector supported by ZigBee Home Automation
1.2. The detector
’s features are as follows:
A. Red LED
B. Green LED
C. Tamper Switch
5. SPECIAL COMMENTS
Even the most sophisticated detectors can sometimes be defeated or may fail to warn due to: DC power failure
/ improper connection, malicious masking of the lens, tampering with the optical system, decreased sensitivity in
ambient temperatures close to that of the human body and unexpected failure of a component part. The above list
includes the most common reasons for failure to detect intrusion, but is by no means comprehensive. It is therefore
recommended that the detector and the entire alarm system be checked weekly, to ensure proper performance. An
alarm system should not be regarded as a substitute for insurance. Home and property owners or renters should be
prudent enough to continue insuring their lives and property, even though they are protected by an alarm system.
6. COMPLIANCE WITH STANDARDS
FCC Statement: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications not expressly approved by the Ecolink Intelligent Technology Inc. could void the user’s authority to operate
the equipment.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est
soumis aux deux conditions suivantes: (1) cet appareil ne doit pas provoquer d'interférences et (2) cet appareil
doit accepter toute interférence, y compris celles pouvant causer un mauvais fonctionnement de l'appareil.
In accordance with FCC requirements of human exposure to radiofrequency fields, the radiating element shall be
installed such that a minimum separation distance of 20 cm is maintained from the general population.
Conformément aux exigences d'Industrie Canada en matière d'exposition humaine aux champs de
radiofréquences, l'élément rayonnant doit être installé de telle sorte qu'une distance minimale de 20 cm soit
maintenue par rapport à la population générale.
FCC ID: XQC-PIRZB1ECO
IC
ID: 9863B-PIRZB1ECO
Installation shall be done in accordance with the Standard for Installation and Classification of Burglar and Holdup Alarm Systems, UL 681.
2. SPECIFICATIONS
Detector Type:
Two - Dual element low-noise pyroelectric sensor
Optical Data:
18 parabolic mirrors for long range
18 parabolic mirrors for close range
Max. Coverage:
15 x 15 m, (49.2 x 49.2 ft) / 90°
Pet Immunity:
Selectable: (1.No immunity 2. Up to 40 lb 3. Up to 85 lb)
ELECTRICAL
Internal Batteries:
Two 3V Lithium batteries, type CR-123A. For UL installations, use Panasonic only
Nominal Battery Capacity:
1400 mAh per battery
Battery Life (with LED on):
Typically over 5 years
Note: Inability to connect with wireless network, or wireless link quality resulting in intermittent connection may
significantly reduce the expected battery life.
Battery Power Test:
Performed immediately upon battery insertion and during each transmission to the panel
FUNCTIONAL
Alarm Period:
3 seconds
Visual Indications:
Red LED lights for about 3 seconds upon transmission of alarm & tamper messages and upon motion
Detection in the walk test mode only (walk test mode available for approx. 15 minutes). Red LED flashes during
the power-up stabilization period, or after restoring (pressing) the tamper switch (power-up stabilization period is
approx. 1 minutes). LED does not light upon transmissions of supervision messages or alarm detection after
termination of walk test mode.
Rearm Timer:
Rearms the detector 2 minutes after the last alarm. Timer disabled in the walk test mode.
WIRELESS
Supported Network:
ZigBee H.A 1.2
Frequency:
2.405
– 2.480 Ghz as per IEEE 802.15.4
Tamper Alert:
Reported when a tamper event occurs and in any subsequent message, until the tamper switch is restored
MOUNTING
Height:
1.8-2.4 m (6 - 8 ft). For pet rejection, the optimal height is 2.1 m (7 ft)
Installation Options:
Surface or corner
ENVIRONMENTAL
Operating Temperatures
-
10˚ C to 55˚ C (14˚ F to 131˚ F)
Storage Temperatures
-
20˚ C to 65˚ C (-4˚ F to 149˚ F)
COMPLIANCE WITH STANDARDS
USA
CFR 47 part 15,
ANSI/UL 639
PHYSICAL
Size (H x W x D)
83 x 61 x 42 mm (3.27 x 2.4 x
1.66”)
Weight (with battery)
90 g (3.17 oz)
Color
White
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interferene and (2) this device must accept any interference received, including interference that may
cause undesired operation.
