© Eco Heat Equipment
–
January 2016
2 of 2
Motion Sensor Adjustments
NOTE: The three adjustment controls are connected to the components directly
using a small stopper. Please exercise caution when adjusting, and never attempt
to turn beyond the 270° adjustment range.
The motion sensor’s settings can be adjusted as follows:
Step 1 – Adjust the TIME setting to minimum
Turn the TIME control fully anti-clockwise to set to the 10 second testing setting.
Step 2 – Adjust the LUX/LIGHT setting to maximum
Turn the LUX/LIGHT fully clockwise to set to maximum (sensor functioning in all
lighting conditions).
Step 3 – Adjust the RANGE setting
Turn the RANGE control fully anti-clockwise. Move away from the sensor until the
LED stops blinking. This will be the minimum detection range for the setting. To
increase the range, turn the control clockwise until the desired distance is reached
(2m – 10m maximum).
Step 4 – Adjust the LUX/LIGHT setting
If the LUX/LIGHT control is set to maximum (fully clockwise), the lights will turn ON
whenever the room is occupied, even in full daylight.
Alternatively, turn the LUX/LIGHT anti-clockwise until the desired LUX setting is
achieved.
Step 5 – Adjust the TIME setting
Turn the TIME control clockwise until the desired delay is reached (10 seconds to 30
minutes).
Factory time out is pre set to 10 seconds.
NOTE: All the time intervals are within approximately 10 seconds of the stated time
out interval.
Step 6 – Microphone (audio sensor)
To disconnect the microphone, press the Push button once to activate the manual
override (sensor will turn OFF). Then hold down the Push button until the LED starts
to blink (approximately 5sec). Press the Push button once more to deactivate the
manual override (sensor will turn back ON). The HF sensing will continue to operate
when the microphone is disconnected.
To reconnect the microphone, repeat steps above.
Disabling the microphone is ideal for areas where there are high ambient sound
levels, such as near a busy road or in a shopping center.
NOTE: HF Sensor must first detect motion to switch the device on. Sensor will NOT
switch the device on if no motion is detected.
OTHER CAUTIONS:
Disconnect power when working on electrical outlets or components.
Do not push on the surface of the lens.
Cleaning
Carefully wipe sensor with a soft damp cloth.
Recycling
Please recycle all packaging material that came with the motion sensor.
Warranty
The sensor has a three (3) year warranty after the date of the original purchase.
Please keep your original receipt, as this will be required for any claims under this
warranty. The warranty is a strictly carry in policy. (The sensor/s must be returned to
Eco Heat offices for a claim to be processed).
The warranty does not cover:
§
damage from misuse,
§
neglect or abuse,
§
products that have been modified in any way,
§
shipping and handling cost associated with the product,
§
damage resulting from accidents, lightning, fire, water, power surges,
natural disasters and/or incorrect installation
For more information, view the Return/Refund Policy at www.ecosensor.co.za.
Optional Remote Control
The sensor LED will flash 3 times to
confirm each setting applied
ON=Always on. After about
six hours turns to “AUTO”
mode.
OFF=Always off. After about
six hours turns to “AUTO”
mode.
Automatic ON/OFF
Test mode: Light level will not
influence the operation in this
mode. Use to test and setup
detection range.
Reset: Resetting of all
functions to:
Time: 10sec
Range: Max
Lux: Max
Microphone ON/OFF (if
applicable)
Automatic reading and
saving of the actual light
level
Permanent tamper
protection: Lock all settings
to avoid tampering. Only
On and Off buttons will be
functional.
Lux/Light settings (10 to 2000
Lux).
Recommendation: rooms
with daylight 500 Lux, without
daylight 2000 Lux.
Time settings (10 secs to 30
mins)
Range settings (2m to Max)
Trouble Shooting
Malfunction
Possible Cause
Remedy
The unit will
not switch
“on”
a.
No mains power
b.
No movement is
detected (in detection
zone)
c.
Wrong LUX/LIGHT level
setting
d.
Electrical circuitry faulty
e.
Electrical Installation not
done correctly
f.
Unit may be faulty
a.
Check mains power is on
b.
Move towards the unit (in
detection zone) or increase the
detection range settings
c.
Adjust setting on the LUX/LIGHT
settings
d.
Refer to the ‘Electrical
Installation’ section to ensure
correct installation
e.
Have a certified electrician
disconnect and test the unit
f.
Contact Eco Heat Equipment
Unit stays
“on”
permanently
g.
Continuous movement in
detection zone
h.
The sensor is not
mounted correctly for
reliable operation
i.
Wrong LUX/LIGHT level
setting
j.
Time setting control is set
too far
k.
Unit may be faulty
g. Check detection range setting
and reduce detection range
sensitivity
h. Check detection range setting
and mounting procedure
i. Adjust setting on the LUX/LIGHT
settings
j. Adjust the time setting control
k. Contact Eco Heat Equipment
Due to minor improvements in design or otherwise, the product you purchase
may differ from the one shown in this leaflet. For more information or advice on
this or any other Eco Heat Equipment products, visit www.ecosensor.co.za or
phone +27 (0)861 999 887.
Indemnity: The Author, and supplier, shall not be held liable for any loss, injury or
damage, of whatsoever nature, whether consequential or not, either contractual
sustained to, or caused by, or which may arise through the use of any comments,
suggestions, circuitry, services or equipment offered for purchase. The User,
indemnifies the author and supplier, and agrees not to hold him/her responsible
for any damages, losses and/or liabilities (including legal costs on a scale as
between attorney and user) arising from, or through the use of circuit diagrams,
equipment and services, whether such circuit diagrams, equipment and services
were used with the consent of the User or not. All risks attached to the use of
circuit diagrams, equipment and the connection thereof to the User’s equipment
shall be deemed to have passed onto the User, once having purchased such
equipment from the author or supplier.
OFF
ON
AUTO
TEST
RESET
2000
LUX
500
LUX
10SEC
30MIN
2M
8M
