Eclipse Linnox SP CCS-LS Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 22

Eclipse Linnox SP CCS-LS Скачать руководство пользователя страница 4

Eclipse Linnox Model CCS-LS, Installation Guide 159, 2/20/04

4

There are several special symbols in this document. You must
know their meaning and importance.
Following is an explanation of the symbols. Please read
thoroughly.

Danger:

Indicates hazards or unsafe practices which
WILL result in severe personal injury or even
death. Only qualified and well trained personnel
are allowed to carry out these instructions or
procedures.
Act with great care and follow the instructions.

Warning:

Indicates hazards or unsafe practices which
could result in severe personal injury or damage.
Act with great care and follow the instructions.

Caution:

Indicates hazards or unsafe practices which could
result in damage to the machine or minor personal
injury.
Act carefully.

Note:
Indicates an important part of the text.
Read thoroughly.

If you need help, contact Eclipse Combustion or your local Eclipse
representative.

D

OCUMENT

C

ONVENTIONS

H

OW

TO

G

ET

H

ELP

«
...
2
3
4
5
6
...
»

Содержание Linnox SP CCS-LS























Отзывы:

Нет отзывов