Ecler VEO-XTI2L Скачать руководство пользователя страница 4

 

 

8.

 

Do not install near any heat sources such as radiators, heat registers, stoves, or 

other apparatus (including amplifiers) that produce heat. 

 

9.

 

Do  not  defeat  the  safety  purpose  of  the  polarized  or  grounding  type  plug.  A 

polarized plug has two blades with one wider than the other. A grounding type 

plug  has  two  blades  and  a  third  grounding  prong.  The  wide  blade  or  the  third 

prong  are  provided  for  your  safety.  If  the  provided  plug  does  not  fit  into  your 

outlet, consult an electrician for replacement of the obsolete outlet. 

10.

 

Protect the power cord from being walked on or pinched particularly at the plugs, 

convenience receptacles, and at the point where they exit from the apparatus. 

11.

 

Only use attachments/accessories specified by the manufacturer. 

12.

 

Unplug the apparatus during lightening sorts or when unused for long periods of 

time. 

13.

 

Refer all servicing to qualified personnel. Servicing is required when the apparatus 

has been damaged in any way, such as power supply cord or plug is damaged, 

liquid has been spilled or objects have fallen into the apparatus, the apparatus has 

been  exposed  to  rain  or  moisture,  does  not  operate  normally,  or  has  been 

dropped.

 

14.

 

Disconnecting from mains: Switching off the POWER switch all the functions and 

light indicators of the amplifier will be stopped, but fully disconnecting the device 

from mains is done unplugging the power cord from the mains input socket. For 

this reason, it always shall remain readily operable. 

15.

 

Equipment is connected to a socket-outlet with earthing connection by means of a 

power cord. 

16.

 

The marking information is located at the bottom of apparatus. 

17.

 

The apparatus shall not be exposed to dripping or splashing and that no objects 

filled with liquids, such as vases, shall be placed on apparatus. 

 

NOTE: 

This equipment has been tested and found to comply with the limits for a ClassA 

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference when the equipment is operated in a 
commercial  environment.  This  equipment  generates,  uses,  and  can  radiate  radio 
frequency energy and, if not installed and used in accordance with the instruction manual, 
may cause harmful interference to radio communications. Operation of this equipment in 
a  residential  area  is  likely  to  cause  harmful  interference  in  which  case  the  user  will  be 
required to correct the interference at his own expense.  

 

WARNING

:

 

This product must not be discarded, under any circumstance, as 

unsorted  urban  waste.  Take  to  the  nearest  electrical  and  electronic  waste 
treatment centre. 

NEEC AUDIO BARCELONA, S.L. 

accepts no liability for any damage that may be caused 

to people, animal or objects due to failure to comply with the warnings above. 

Содержание VEO-XTI2L


















Отзывы: