manualshive.com logo in svg

ECKey EK6 series, Инструкция по установке и эксплуатации, Страница: 4 / 15

Поделиться
Скачать
ECKey EK6 series Скачать руководство пользователя страница 4

ECKey Installation and Operation Guide

4.

Bluetooth Modes and Hidden Phones

Two enrolled phones can be defined as 

Hidden

. This allows them to trigger the reader whenever Bluetooth is 

on

, even if

the phone is not 

discoverable

. By default, enrolled phones are not hidden so they must be made 

discoverable

to trigger the

reader.

In most cases Bluetooth will remain on after exiting the Bluetooth settings and when the phone ‘sleeps’, but there are
some phones that simply will not trigger the reader when defined as Hidden (mainly iPhones) – these phones should not
be defined as Hidden Users.

Also, if you’re on a call with a Bluetooth headset or car kit with your Hidden phone, you will still be able to trigger the
ECKey reader without changing Bluetooth modes or interrupting your phone call.

5.

PC Management Software

The PC Management Software requires Windows 7, and an internet connection to obtain installation files and to check for
software updates. It can be downloaded from 

http://www.ECKey.com/download/

. 

Locate the downloaded installation file, right-click on it and choose ‘Run as Administrator.’ Follow the prompts to complete
installation.

You can then connect your PC to the reader using the USB programming cable or over a Bluetooth connection. Both offer
secure methods for administration.

a.

To connect with USB cable

i.

Plug the USB programming cable into the PC.

ii.

Remove the screw at the bottom of the reader and carefully remove the backplate.

iii.

Connect the red connector on the USB cable to the red connector on the reader. Use care when connecting 
the USB cable – both connectors are keyed and must be aligned properly.

iv.

The status light should be red and drivers should be installing on the PC. If the PC does not automatically 
install drivers, they can usually be obtained through Windows Updates or can be manually downloaded 
from 

http://www.ECKey.com/download/

.

v. 

Launch the PC Management Software. At the ECKey Connection Window, select the radio button for 
‘Connect Via Cable or Bluetooth COM Port.’ If necessary, click the Detect or Refresh buttons to update 
the active COM ports. 

vi.

Select the appropriate COM port that is associated with the reader and click ‘Connect’. You will be 
prompted to enter the Manager PIN (default is 12345678) if the reader is configured for Secure Reader 
Mode – this is enabled by a checkbox on the Security Tab (this option is off by default). 

b.

To connect with Bluetooth

i.

Turn on the PC’s Bluetooth radio. There may be a button or switch that enables Bluetooth. If the PC is not
Bluetooth ready, we recommend using a 3rd party radio with a CSR chipset that supports Classic Bluetooth.

ii.

Place the reader in admin mode by pressing the Administration button for about 3 seconds until status light 
flashes blue/red. Release Admin button. Press and hold the Admin button a second time for about 3 seconds 
until status light is solid yellow.

iii.

Launch PC Management Software. At the ECKey Connection Window, select the radio button for Direct 
Bluetooth Connection and click the ‘Detect’ button to the right. This will display all readers in range, as well 
as previously connected readers that may not be present.

iv.

Highlight the correct reader and click ‘Connect’

v.

Enter the Manager PIN (default is 12345678) – the status light should be yellow with an occasional blue 
flash. 

4

Содержание EK6 series
















Отзывы:

Нет отзывов