background image

Page 1

RVS-RCS Installation Guide

RVS/RCS

This guide covers all models of RVS vacancy and RCS occupancy ceiling sensors. 

These models include:

RVS-A-

X

W       Vacancy sensor with small motion short range lens (1000 sq. ft.)

RVS-B-

X

W       Vacancy sensor with large motion large range lens (1900 sq. ft.)

RVS-DA-

X

W    Dual-tech vacancy sensor with small motion short range lens (1000 sq. ft.)

RVS-DB-

X

W    Dual-tech vacancy sensor with large motion large range lens (1900 sq. ft.)

The RCS models are identical to the RVS with the addition of a battery to provide power for 

support of auto-on occupancy sensor applications.   

The character 

X

  in  the  model  number  is  replaced  with  U  for  902MHz,  Y  for  868MHz 

radios, and J for 928MHz radios. 

The product box includes the sensor, installation guide, lens mask, and two wire straps 

for ceiling tile mounting.   

i

Note:

The sensor cover is removable however it must be properly 

seated for normal operation

i

Note:

The RVS is a solar powered device that absorbs solar energy 

from artificial or natural light sources. Before assigning the RVS 

sensor to a receiver or controller, the sensor should be exposed 

to a good light source for a minimum of 2 minutes.

RVS - Vacancy, RCS - Occupancy Sensor Description

The RVS/RCS (also referred to as the sensor in this guide) is a wireless, energy harvesting 

sensor.  The  models  include  a  single  method  PIR  (passive  infrared)  sensor  or  a  dual 

technology  method of occupancy detection using a PIR sensor and audio interface (any 

reference to audio in this guide applies to DT models only). The combination of PIR sensor 

and  audio  sensing  adds  additional  assurance  of  positive  occupant  detection.  Passive 

microphone technology provides coverage of audible human activity across most of the 

PIR detection range. Innovative noise filtering is used to prevent false triggers that could 

keep lights on in empty rooms. Used for indoor applications, the detector is optimized 

for ceiling heights of 8 - 10 feet (2.4 - 3 meters).

Wireless Vacancy/Occupancy 

pir or dual-tech Sensor

Installation Guide

Содержание RVS-A-XW









Отзывы: