manualshive.com logo in svg

Echo WP-1000, Руководство оператора

Поделиться
Скачать
Echo WP-1000 Скачать руководство пользователя страница 24

24

X7505120800

© 4/2015 ECHO Inc.

MAINTENANCE

WP-1000

3. Use brush to remove dirt from the cylinder fins. 

4. Remove grass and leaves from the grid between the starter 

and fuel tank.

5. When installing the cover, be certain the tab of the metal 

deflector shield is in the slot of the cover.  

6. Assemble components in reverse order.

Exhaust System

Spark Arrestor Screen

Level 2.

1. Remove engine cover. See “Cleaning Cooling System” for 

step by step instructions. 

2. Place piston at Top Dead Center (TDC) to prevent 

carbon/dirt from entering cylinder.

3. Remove screen cover (A), screen holder (B), gasket (C), 

and spark arrestor screen (D) from muffler body.

4. Clean carbon deposits from screen (D) and muffler 

components.

Note:  When cleaning carbon deposit, be careful not to damage 

the catalytic element inside muffler.

5. Replace screen if it is cracked, plugged, or has holes burned through.

6. Assemble components in reverse order.

Parts Required:

Spark Arrestor Screen, Gasket

Содержание WP-1000









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды