background image

SRM-5000

10-52D-02

1

lNTRODUCTION

We are constantly working on technical

improvement of our products. For this reason,

technical data, equipment and design are

subject  to  change  without  notice.  All

specifications, illustrations and directions in

this SERVICE DATA are based on the latest

products information available at the time of

publication.

ECHO  SERVICE  MANUAL  Ord.  402-25

(Model : SRM-4000, RM-4000) contains lots

of information for servicing this model.

NOTE : SRM-5000 serial number 36000001 to

36007482. Refer to Service Data 10-52C-01.

1

CONTENTS

page

1 SERVICE INFORMATION ............................. 2

1-1 Specification ............................................... 2

1-2 Technical data ............................................ 3

1-3 Torque limits ............................................... 4

1-4 Special repairing materials ........................ 4

1-5 Service limits .............................................. 5

1-6 Special tools ............................................... 6

2 EMISSION ADJUSTMENT GUIDE ............... 7

2-1 General adjusting rules .............................. 7

2-2 Idle adjust screw, idle mixture needle and

      H mixture needle initial settings .................. 7

2-3 Adjusting carburettor .................................. 8

Reference No.

10-52D-02

R E V I S E D :   2 0 0 6 0 9

INDEX

ISSUED: 200510

Содержание SRM-5000










Отзывы: