background image

- 9 -

WARNING          DANGER

GRASS/WEED TRIMMERS CAN  THROW
GRAVEL, STONE, WOOD CHIPS, GLASS, AND
PLASTIC OR METAL OBJECTS. THE DEBRIS
SHIELD BEHIND THE TRIMMER  HEAD  STOPS
MUCH OF THE DEBRIS, BUT CANNOT
PREVENT THE OPERATOR FROM BEING
STRUCK BY SOME DEBRIS. READ THE RULES
FOR SAFE OPERATION IN THE OPERATOR’S
MANUAL THAT YOU RECEIVED WITH YOUR
ECHO TRIMMER. AISO, FOLLOW AII
INSTRUCTIONS IN THIS INSTRUCTION SHEET.

ECHO 2-LINE MANUAL TRIMMER HEAD
(OPTION)

1.

Read the Operator’s Manual carefully. Be throughly
familiar with the controls and proper use of the
trimmer.
Know how to stop the unit and disengage the
controls.

2.

Never allow children to operate the trimmer.

3.

Never allow adults to use the trimmer unless they
have received prpper instructions. Be sure the
operator is properly attired and wears the type of
foot, leg, head, eye and ear protection
recommended both in your ECHO Operator's
Manual and by your ECHO Servicing Dealer.

4.

Always wear eye protection that conforms to
A.N.S.I.Z87.1-1979.

1. REPLACING LINE

A. Remove spool by turning knob clockwise, “right”,

and separating parts.

B. Thread a 6 m (20 feet) length of 2.4 mm (.095 inch)

or 2.7 mm (.105 inch) ECHO line through hole in
spool so that ends are the same length.

C. Wind both ends of line tightly and evenly clockwise

(see arrows on spool), and wind from side to side
without twisting the lines.

D. Secure ends of line temporarily with about 15 cm

(6 inch) extending out.

NOTE

Keep line tight on spool.

A. Snap spool into housing while pulling line through

eyelets with about 15 cm (6 inch) extending out.

CAUTION

Knob tightens counterclockwise, “left”.

B. Fasten spool to housing with shaft bolt, spring,

and knob.

2.REPLACING SPOOL

1C
1D

HOUSING

BOLT

SPRING

KNOB

1B

2A

15 cm (6 inch)

SPOOL

2B

Содержание SRM-3800 TYPE 1-E






















Отзывы: