background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

17

P

RE

 - O

PERATION

FUEL

Fuel Requirements

Gasoline - Use 89 Octane [        ] (mid grade or higher) gasoline known
to be good quality. Gasoline may contain up to 15% MTBE (methyl
tertiary-butyl ether). Gasohol containing methyl (wood) alcohol is NOT
approved.

Two Stroke Oil - A two-stroke engine oil meeting ISO-L-EGD (ISO/CD
13738) and J.A.S.O. FC Standards, must be used. Echo brand Premium
50:1 oil meets these standards. Engine problems due to inadequate
lubrication caused by failure to use an ISO-L-EGD and J.A.S.O. FC
certified oil, such as Echo Premium 50:1 Two-stroke Oil, will void the
two-stroke engine warranty.  (Emission related parts only are covered
for two years, regardless of two-stroke oil used, per the statement listed
in the California Emission Defect Warranty Explanation.)

IMPORTANT
Echo Premium 2-Stroke Oil may be mixed at 50:1 ratio for application
in all Echo engines sold in the past regardless of ratio specified in
those manuals.

Mixing Instructions
1.

Fill an approved fuel container with half of the required amount of
gasoline.

2.

Add 2-stroke oil to gasoline.

3.

Close container and shake to mix oil with gasoline.

4.

Add remaining gasoline and remix.

5.

Install fuel container cap and wipe any spilled fuel from container
and surrounding area.

Handling Fuel

WARNING  

   DANGER

Fuel is VERY flammable. Use extreme care when mixing, storing or
handling, otherwise serious personal injury may result.
• Use an approved fuel container.
• DO NOT smoke near fuel.
• DO NOT allow flames or sparks near fuel.
• Fuel tanks/cans may be under pressure.  Always loosen fuel caps

slowly allowing pressure to equalize.

• NEVER refuel a unit when the engine is HOT!
• NEVER refuel a unit with the engine running.
• DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors

over bare ground.

• Securely tighten fuel cap after refueling.
• Inspect for fuel leakage. If fuel leakage is found, do not start or

operate unit until leakage is repaired.

R + M

2

IMPORTANT
Spilled fuel is a leading cause of
hydrocarbon emissions. Some states
may require the use of automatic fuel
shut-off containers to reduce fuel
spillage. Contact your ECHO dealer for
ordering information.

After Refueling;

• Wipe any spilled fuel from the unit.
• Move at least 3m (10 ft.) from refueling

location before starting.

After Use;

• DO NOT store a unit with fuel in its tank.

Leaks can occur. Return unused fuel to an
approved fuel storage container.

Storage -

Fuel storage laws vary by  locality. Contact
your local government for the laws affecting
your area. As a precaution, store fuel in an
approved, air tight container. Store in a well
ventilated, unoccupied building, away from
sparks and flames. Do not store fuel longer
than 30 days.

IMPORTANT
Stored fuel ages. Do not mix more fuel
than you expect to use in thirty (30)
days, ninety (90) days when a fuel
stabilizer is added.

IMPORTANT
Stored two-stroke fuel may separate.
ALWAYS shake fuel container
thoroughly before each use.

Содержание SRM-261

































Отзывы: