background image

4

Shaft Decal

WARNING  

  DANGER

• This unit can be dangerous and cause serious injury if improperly

used.  To reduce injury risk to operator, helpers and bystanders, read
and understand  the Operator's and Safety manuals.

• Blindness can occur from objects that are thrown or ricocheted even

with shield in place.  Operators, helpers and bystanders must wear
ANSI Z87.1 approved eye protection.

• Always wear hearing protection when operating unit.
• Prevent accidental contact with unit and any cutting attachment.

Maintain a 50 ft. (15M) radius, DANGER ZONE surrounding the
operator. ONLY the operator, dressed in proper protective clothing
should be in the DANGER ZONE.

• Beware of KICKOUT (blade thrust) when using blades. Special

 precautions are necessary for blade operation, see your Operator's
and Safety Manuals.  ONLY install ECHO approved blades on Brush
Cutters (SRM) models equipped with proper blade shield,   U-handles,
harness, blade collar, nut and cotter pin.

• Blade/Cutting attachment does not stop immediately after releasing

throttle. Keep hands and feet clear of blade/cutting attachment unless
engine is shut off and cutting attachment is not moving.

• INSPECT BLADES BEFORE USE.
• DO NOT USE DAMAGED, CRACKED, BENT, DULL OR

IMPROPERLY SHARPENED BLADES.

• Do not remove shields, modify the unit or install attachments or parts

not approved by ECHO.  Approved attachment information and
replacement Operator's and Safety Manuals are available from your
ECHO dealer or by writing: ECHO, INCORPORATED,
400 OAKWOOD RD., LAKE ZURICH, IL  60047.

INTERNATIONAL

 

SYMBOLS

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

Hot

Surface

Carburetor adjustment

- Idle speed

Carburetor adjustment

- High speed mixture

Symbol

description/application

Symbol form/shape

Symbol

description/application

Symbol form/shape

"WARNING, SEE

OPERATOR'S

MANUAL

Wear eyes, ears and

head protection

Emergency stop

Fuel and oil mixture

Finger Severing

Carburetor adjustment

- Low speed mixture

Primer Bulb

Ignition
ON/OFF

Wear hand and

foot protection

Safety/Alert

Keep bystanders and helpers

away 15 m (50 ft.).

DO NOT smoke

near fuel.

DO NOT allow

flames or sparks

near fuel.

P/N 89016054130

Choke Control

"Cold Start"

Position

(Choke Closed)

Choke Control

"Run"

Position

(Choke Open)

Содержание SRM-210i



































Отзывы: