background image

G

RASS

 T

RIMMER

/B

RUSH

 C

UTTER

O

PERATOR

'

S

 M

ANUAL

15

POWER

 

HEAD

 

SHAFT

/

LOWER

 

SHAFT

 

ASSEMBLY

Tools Required: None

Parts Required: Power Head Shaft, Lower Shaft Assembly

1. Set Power Head/Shaft Assembly on a level surface.

2. Loosen clamping knob (A).

3. Pull locator pin (B) and rotate counter clockwise 1/4 turn to lock

out position.

4. Carefully fit lower drive shaft assembly into coupler (C) to decal

assembly line (D), making sure that the inner lower drive shaft
engages into the upper drive shaft mount.

NOTE
Lower bearing housing and head assembly must be in line with the
engine.

5. Rotate locator pin (B) 1/4 turn clockwise to engage lower drive shaft

hole. Insure locator pin is fully engaged by gently twisting lower
drive shaft. Locator pin should snap flush in coupler. Full engage-
ment will prevent further shaft rotation.

6. Secure lower shaft assembly to coupler by tightening clamping

knob (A).

PLASTIC

 

SHIELD

 

INSTALLATION

(For Nylon Line Operation)

Tools Required: Screwdriver.

Parts Required: Plastic Shield, Shield Plate, three (3) 5 mm x 15 mm
screws.

NOTE
The plastic shield is for use with the Nylon Line Head only.  Install
Metal Shield when using plastic or metal blades.

1. Snap the shield on the bottom of the bearing housing flange.

2. Place shield plate on shield, align holes and install three (3) screws.

A

C

B

D

B

C

A

Содержание SRM - 2100SB





































Отзывы: