background image

6

e

mIssIon

 C

onTrol

 (

exhausT

 & 

evaporaTIve

)

EPA 2010 and Later and/or C.A.R.B. TIER III

The emission control system for the engine is EM/TWC (Engine Modification and 3-way Catalyst) and for the fuel tank the 

Control System is EVAP (Evaporative Emissions) or N (for nylon tank). Evaporative emission may be applicable to Califor-

nia models only.

An Emission Control Label 

is located on the engine.  (This is an EXAMPLE ONLY; information on label varies by 

engine FAMILY).

PRODUCT  EMIssION  DURABILITY  (EMIssION COMPLIANCE PERIOD)

The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine 

emissions output meets applicable emissions regulations, provided that approved maintenance procedures are 

followed as listed in the Maintenance section of this manual.

equIpmenT

 

CheCk

  

  WARNING

Use only ECHO approved attachments. Serious injury may result from the use of a non-approved attachment combi

-

nation. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have 

not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety 

manual.

•  Check unit for loose/missing nuts, bolts and screws. Tighten and/or replace as needed.                                                                               

•  Do not use blower if any part is missing or damaged.

•  Have repairs done only by an authorized ECHO Service dealer.

•  Do not use any attachment, accessory or replacement part unless it is recommended in this Operator's Manual.

 

WARNING

Moving parts can amputate fingers or cause severe injuries.  Keep hands, clothing and loose objects away from all 

openings.     

• 

ALWAYs

 stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop  

before removing obstructions, clearing debris, or servicing unit.

• 

DO NOT

 start or operate unit unless all guards and protective covers are properly assembled to unit.

• 

NEVER

 reach into any opening while the engine is running.  Moving parts may not be visible through openings.

 

WARNING

Check fuel system for leaks due to fuel tank damage, especially if the unit is dropped. If damage or leaks are found, 

do not use unit, otherwise serious personal injury or property damage may occur. Have unit repaired by an authorized 

servicing dealer before using.

Содержание Pro Attachment ES-210

































Отзывы: