background image

20

X7504083607

© 9/2014 ECHO Inc.

OPERATION

TC-210

TILLING - Recommended tilling depth is 15-20 cm (6 - 8 
inches

)           

Install Tines with individual tines angled forward, toward front of 
unit. (See Tine Removal/Cleaning/Installation)

• Use a forward/backward motion to till soil.  Allow tines to dig 

into soil, then pull unit back to break up and pulverize clumps.  
Tilling depth is controlled by the number of times the 
forward/backward motion is used in an area.

• Controlling tilling depth :

• Shallow tilling: Move tiller over soil surface quickly.  Tines should be in  cultivating position.

• Deeper tilling: Move tiller over soil slowly.  Allow tiller to work the same area until desired depth is reached.

• Big Weeds/Tough Roots: Rock tiller back and forth over tough spot until the tines slice through the roots or 

weeds.

• Digging Holes: Hold tiller in place, and allow tines to dig down 

into the soil.  Allow tines to dig approximately 6 – 8  inches 
deep, then lift unit up and out.  Remove loose soil with shovel 
or rake.  Resume digging with rotating tiller tines until desired 
depth is reached.  

CULTIVATING – Recommended cultivating depth is 5-7.5 
cm (2 – 3 inches

). Install Tines with individual tines angled 

rearward, toward the operator.

(See Tine Removal/Cleaning/Installation) 

Allow unit to move 

forward slowly.  Pull unit back to cut vegetation and cultivate soil 
to desired depth. Repeat forward/backward motion as needed.

TILLING

CULTIVATING

Содержание Operator's Manual





































Отзывы: