background image

6

SAFE

 

OPERATION

WARNING  

  DANGER

Do not operate this product indoors or in inadequately ventilated
areas. Engine exhaust contains poisonous emissions and can cause
serious injury or death.

Read the Manuals
• Provide all users of this equipment with the Operator's Manual and

Safety Manual for instructions on Safe Operation.

Clear the Work Area
• Spectators and fellow workers must be warned, and children and

animals prevented from coming nearer than 15 m (50 ft.) while the unit
is in use.

Keep a Firm Grip
• Hold the front and rear handles with both hands, with thumbs and

fingers tightly encircling the handles.

Keep a Solid Stance
• Maintain footing and balance at all times. Do not stand on slippery,

uneven or unstable surfaces. Do not work in odd positions or on
ladders. Do not over reach.

EQUIPMENT

WARNING  

  DANGER

Use only ECHO approved attachments. Serious injury may result from the use of a non approved attachment combi-
nation. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have
not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual and safety
manual.

• Check unit for loose/missing nuts, bolts and screws. Tighten and/or

replace as needed.

• Inspect fuel lines, tank and area around carburetor for fuel leaks.

DO NOT operate unit if leaks are found.

• Inspect shield for damage and ensure that the cut-off knife issecurely

in place. Replace if either is damaged or missing.

• Check that the cutting attachment is firmly attached and in safe

operating condition.

• Check that front (loop) handle and optional shoulder/waist harness

are adjusted for safe, comfortable operation. See Assembly for proper
adjustment.

• Have repairs done only by an authorized ECHO Service Dealer.
• Keep exhaust area clear of flammable debris. Avoid contact during

and immediately after operation.

Содержание GT-200R - 11-03

























Отзывы: