background image

2

WARNING         DANGER

ALWAYS STOP THE ENGINE WHEN A
DRILL JAM OCCURS. DO NOT ATTEMPT
TO REMOVE AN OBJECT CAUSING A
DRILL JAM IF THE ENGINE IS RUNNING.
PHYSICAL INJURY CAN OCCUR IF A
DRILL JAM IS REMOVED AND THE
DRILLS START MOVING.

Do all drilling at full throttle speed. Drilling
at less at than full speed can damage the
clutch by allowing it to slip.

WARNING         DANGER

USE A FIRM GRIP WITH THUMBS AND
FINGERS ENCIRCLING THE HANDLES. A
FIRM GRIP WILL HELP YOU KEEP
CONTROL OF THE ENGINE DRILL.
NEVER OPERATE THE ENGINE DRILL
ONLY ONE HAND OR BODILY INJURY
CAN OCCUR.

Always carry the engine drill with the
engine stopped and the HOT muffler away
from your body.

PROTECTIVE EQUIPMENT

Always wear eye protection goggles that
meet ANSI Z87.1 standards.

Wear hearing protection.
ECHO recommends that hearing protection
be worn at all times.

Dress properly! Do not wear loose clothing
or jewellery, they can be caught in moving
parts. Use of sturdy gloves, non-skid
footwear, and safety glasses is
recommended.

While operating the machine always be
sure of a secure position.

WARNING         DANGER

ENGINE DRILL USERS RISK INJURY TO
THEMSELVES AND OTHERS IF THE
ENGINE DRILL IS USED IMPROPERLY,
AND/OR SAFETY PRECAUTIONS ARE
NOT FOLLOWED. PROPER CLOTHING
AND SAFETY GEAR MUST BE WORN
WHEN OPERATING ENGINE DRILL.

OPERATOR SAFETY

Read this Engine drill Operator’s Manual
carefully. Be sure you understand how to
operate this unit properly before you use it.

Be familiar with all the controls and the
proper use of the machine.

Wear proper clothing to protect legs and
other exposed parts of your body.

Wear non-skid sole shoes. Do not wear
open-toed shoes or operate unit while bare
footed.

Wear eye and hearing protection devices.

Use caution when handling fuel. Put the
caps back tightly on both the fuel can and
the engine drill fuel tank.
Move at least 3 meters (10 feet) from the
re-fuelling point and be sure there is no
leakage of fuel from the fuel tank cap or the
fuel system before starting the engine.

Operate this gasoline powered engine
equipment in a well-ventilated area only.

Start the unit on the ground with the throttle
set at idle. Do not start if the drills are
obstructed by the ground or any other
object.

Never allow children to use the machine.

Do not allow anyone to hold the material
you are drilling.

Keep a firm grip on the engine drill with both
hands, the right hand on the front handle,
the left hand on the rear handle.

SAFETY

Содержание ED-2000

















Отзывы: