manualshive.com logo in svg
background image

10

TROUBLE SHOOTING

         Trouble

Engine -

starts hard

                     Cause

Remedy

-

does not start

Engine

Fuel at

No fuel

• Fuel filter clogged

• Clean or replace

cranks

carburetor

at carburetor

• Fuel line clogged

• Clean

• Carburetor

• Ask your ECHO dealer

Fuel at

No fuel at

• Carburetor

• Ask your ECHO dealer

cylinder

cylinder

Silencer wet

• Fuel mixture is too rich

• Open choke

with fuel

• Clean/replace air filter

• Adjust carburetor

• Ask your ECHO dealer

Spark at

No spark at

• Ignition switch off

• Turn switch on

end of

end of plug

• Electrical problem

• Ask your ECHO dealer

plug wire

wire

Spark at

No spark at

• Spark gap incorrect

• Adjust 0.6 to 0.7 mm

plug

plug

    (0.024 to 0.028 in)

• Covered with carbon

• Clean or replace

• Fouled with fuel

• Clean or replace

• Spark plug defective

• Replace plug

Engine

• Internal engine problem

• Ask your ECHO dealer

does not

crank

Engine

Dies or

• Air filter dirty

• Clean or replace

runs

accelerates poorly

• Fuel filter dirty

• Clean or replace

• Fuel vent blocked

• Clean

• Spark plug

• Clean and adjust/replace

• Carburetor

• Adjust

• Cooling system blocked

• Clean

• Exhaust port/spark arrestor

• Clean

  screen blocked

WARNING         DANGER

ALL ENGINE DRILL SERVICE, OTHER THAN
ITEMS LISTED IN THE OPERATOR’S
MANUAL SHOULD BE PERFORMED BY AN
AUTHORIZED ECHO DEALER.

Содержание ED-200

















Отзывы: