manualshive.com logo in svg

Echo CS-500P, Инструкция по эксплуатации

Поделиться
Скачать
Echo CS-500P Скачать руководство пользователя страница 16

14

CS-500P

CHAIN LUBRICANT

Proper lubrication of the chain while in operation
reduces the friction between the chain and the
guide bar to a minimum and assures a longer
service life.

• Use bar and chain oil of high quality for this

purpose.

• Do not use used or reclaimed oil to avoid various

oiler problems.

• Use ECHO bar and chain oil.
• When ECHO bar and chain oil is not available:

Use motor oil, etc.

• Use bar and chain oil of the following grades:

SAE No. 30 ....... in summer
SAE No. 10 ....... in winter or when cutting

resinous trees.

• When refueling, also refill chain oil.

OPERATION

   WARNING

• After choke control knob is pulled and then

knob is returned to original position,
throttle remains a little open (latch
condition).

• If engine is started in this latch condition,

chain starts to turn. Do not start engine
before chain brake is locked.

   CAUTION

• After starting the engine, squeeze throttle

trigger slightly to release throttle latch and
pull front hand guard towards the operator
immediately.
(Chain brake unlocked position)

• Never use throttle latch for cutting.

• Use the chain brake only in starting or in

emergencies.

Oil tank cap

Fuel tank cap

Cap indication

Oil/fuel tanks are indicated by the following
illustrations on the caps.

Starter handle

Ignition switch

Unlock chain brake

Chain brake

Throttle trigger
lockout

Throttle trigger

Choke

Содержание CS-500P





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды