Echo CS 450 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 48

background image

32

X7503196706

© 09/2013 ECHO Inc.

MAINTENANCE

CS-450

Exhaust Port Cleaning

Level 2.

1. Remove air cleaner cover and remove spark plug lead.

2. Remove guide bar and saw chain. See "Guide Bar and Saw

Chain Installation/Removal."

3. Remove muffler support bracket (A).

4. Place piston at top dead center.

5. Remove muffler. Check parts for wear or damage, and

replace if necessary.

6. Use a wood or plastic scraping tool to clean deposits from

cylinder exhaust port.

Never use a metal tool to scrape carbon from the exhaust port.
Do not scratch the cylinder or piston when cleaning the exhaust
port. Do not allow carbon particles to enter the cylinder.

7. Install muffler. Tighten muffler mounting bolts (or nuts) to

7-11 N•m (60-95 in•lbf).

8. Install muffler support bracket (A).

9. Install guide bar and saw chain. See "Guide Bar and Saw

Chain Installation/Removal."

10. Install spark plug lead and air cleaner cover.

11. Start engine, and warm to operating temperature. Stop

engine.

12. Remove air cleaner cover and remove spark plug lead.

13. Remove guide bar and saw chain. See "Guide Bar and Saw Chain Installation/Removal."

14. Remove muffler support bracket.

15. Re-tighten mounting bolts (or nuts) to 7-11 N•m (60-95 in•lbf).

16. Install muffler support bracket.

17. Install guide bar and saw chain. See "Guide Bar and Saw Chain Installation/Removal."

18. Install spark plug lead and air cleaner cover.

Parts Required:

As needed: Muffler gasket

A

«
...
30
31
32
33
34
...
»

Содержание CS 450

















































Отзывы:

Нет отзывов

Похожие инструкции для CS 450

Бренд: YATO Страницы: 96

Бренд: B&Q Страницы: 65

Бренд: Troy-Bilt Страницы: 22

Бренд: Crown Страницы: 140

Бренд: Craftsman Страницы: 56

Бренд: Craftsman Страницы: 30

Бренд: Craftsman Страницы: 68

Бренд: Craftsman Страницы: 23

Бренд: Craftsman Страницы: 18

Бренд: Craftsman Страницы: 27

Бренд: Craftsman Страницы: 58

Бренд: Craftsman Страницы: 23

Бренд: Craftsman Страницы: 33

Бренд: Craftsman Страницы: 29

Бренд: Craftsman Страницы: 17

SUNJOE 24V-X2-CS16-CT

Бренд: SNOWJOE Страницы: 28

sunjoe iON100V-18CS-CT

Бренд: SNOWJOE Страницы: 28

Бренд: Dolmar Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды