background image

16

CS-400

WHEN THE ENGINE IS COLD 

 

   CAUTION

Make sure the bar and chain are free from any 
obstruction when starting the chain saw.

•  Move chain brake lever fully forward to lock chain 

brake before starting.

•  Fill the fuel tank with fuel mixture.  

 

 

It is not permitted to fill fuel above the shoulder level of 

fuel tank.

•  Fill the chain oil tank with lubricant. Do not over fill.

•  Move ignition switch to “RUN” position.

•  Push purge pump 3 to 4 times or until fuel is visible in 

purge pump.

•  Pull choke control knob all the way out. (Choke posi

-

tion)

NOTE

Do not pull starter rope out to the maximum pos-
sible position.

Do not allow recoil handle to snap back against the 

casing.

OPERATION

Chain brake

Choke

Choke control knob

Purge pump

 

WARNING

  Moving parts can amputate fingers or cause severe injuries.  Keep hands, clothing and loose objects away from 

all openings.  Always stop engine, disconnect spark plug, and make sure all moving parts have come to a com

-

plete stop before removing obstructions, clearing debris, or servicing unit.

  

 WARNING 

Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas.  Breathing CO can cause uncon

-

sciousness, serious injury, or death. Exhaust can cause serious burns.  ALWAYS position unit so that exhaust is 

directed away from your face and body.

  

 WARNING

Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped 

with a spark arrestor and a spark arrestor may be required.  The operator should contact local fire agencies for 

laws or regulations relating to fire prevention requirements.

14

CS-400

Oil tank cap

Fuel tank cap

Cap indication
Fuel/oil tanks are indicated by the following
illustrations.

CHAIN LUBRICANT

Proper lubrication of the chain while in operation
reduces friction between the chain and the guide
bar to a minimum and assures a longer service life.

• Use bar and chain oil of high quality for this

purpose.

• Do not use used or reclaimed oil to avoid various

oiler problems.

• Use ECHO bar and chain oil.
• When ECHO bar and chain oil is not available:

Use motor oil, etc.

• Use bar and chain oil of the following grades:

SAE No. 30 .......in summer
SAE No. 10 .......in winter or when cutting

resinous trees.

• When refueling, also refill chain oil.

OPERATION

   WARNING

• After choke control knob is pulled and then

knob is returned to original position,
throttle remains a little open (latch

condition).

• If engine is started in this latch condition,

chain starts to turn. Do not start engine
before chain brake is activated.

   CAUTION

• After starting the engine, squeeze throttle

trigger slightly to release throttle latch and
pull front hand guard towards the operator
immediately.
(Chain brake unlocked position)

• Never use throttle latch for cutting.
• Use the chain brake only in starting or in

emergencies.

Start / Run

Ignition switch

Chain brake

Starter handle

Unlock chain brake

Choke

Choke control knob

Purge pump

Содержание CS-400 - 04-09





































Отзывы: