background image

CS-3700ES, CS-4200ES

01-36C-01

1

INTRODUCTION

We are constantly working on technical

improvement of our products. For this reason,

technical data, equipment and design are

subject  to  change  without  notice.  All

specifications, illustrations and directions in

this SERVICE DATA are based on the latest

products information available at the time of

publication.

ECHO  SERVICE  MANUAL  Ord.  401-

21(Model : CS-4200, CS-4400) contains lots

of information for servicing this model.

Introduction of primer and carburettor change

on CS-3700ES are informed by Technical

Information No. 2006-324.

0

CONTENTS

page

1 SERVICE INFORMATION .............................

2

1-1 Specification ............................................... 2

1-2 Technical data ............................................ 3

1-3 Torque limits ............................................... 4

1-4 Special repairing materials......................... 4

1-5 Service limits .............................................. 5

1-6 Special tools ............................................... 6

2 EMISSION ADJUSTMENT GUIDE ...............

7

2-1 General adjusting rules .............................. 7

2-2 Presetting idle adjust screw, L mixture needle

and H mixture needle .......................................  8

2-3 Adjusting carburettor..................................  9

Reference No.

01-36C-01

R E V I S E D :   2 0 0 6 0 7

INDEX

ISSUED: 200409

Содержание CS-3700ES










Отзывы: