Echo CS-3000 Скачать руководство пользователя страница 3

Страница: 3 / 24

7. Keep all parts of your body away from the saw

chain when the engine is running.

8. Before you start the engine, make sure that

the saw chain is not contacting anything.

9. Carry the chain saw with the engine stopped,

the guide bar and saw chain to the rear, and
the muffler away from your body.

10. Do not operate a chain saw that is damaged,

improperly adjusted, or not completely and
securely assembled. Be sure that the saw
chain stops moving when the throttle control
trigger is released.

11. Shut off the engine before setting the chain saw

down.

12. Use extreme caution when cutting small size

brush and saplings because slender material
may catch the saw chain and be whipped to-
ward you or pull you off balance.

13. When cutting a limb that is under tension, be

alert for spring back so that you will not be
struck when the tension in the wood fibers is
released.

14. Keep the handles dry, clean, and free of oil or

fuel mixture.

15. Operate the chain saw only in well-ventilated

areas.

16. Do not operate a chain saw in a tree unless

you have been specifically trained to do so.

17. All chain saw service, other than the items listed

in the Instruction Manual maintenance instruc-
tions, should be performed by competent chain
saw service personnel. (For example, if im-
proper tools are used to remove the flywheel
or if an improper tool is used to hold the fly-
wheel in order to remove the clutch, structural
damage to the flywheel could occur and could
subsequently cause the flywheel to burst.)

18. When transporting your chain saw, use the

appropriate guide bar scabbard.

19. Spark arrester mufflers approved to SAE Stan-

dard J335b are Standard on ECHO Chain
saws to reduce the possibility of forest fires.
Do not operate the chain saw with a loose or
defective muffler. Do not remove the spark ar-
rester screen.

CONTENTS

Page

Rules for Safe Operation .................................................................................................. 2

Technical Data ................................................................................................................. 4

Nomenclature of Parts ...................................................................................................... 5

Preparation for Use .......................................................................................................... 6

Fuel and Lubricant ............................................................................................................ 7

Operation ......................................................................................................................... 8

Cutting Instructions ......................................................................................................... 10

Maintenance and Care ................................................................................................... 14

Chain and Guide Bar Combinations ............................................................................... 17

Setting the Saw Chain .................................................................................................... 17

Troubleshooting .............................................................................................................. 19

Storage .......................................................................................................................... 20

Correct Use of Chain Brake ........................................................................................... 21

Servicing Information ...................................................................................................... 24

Содержание CS-3000

























Результаты поиска

Содержание CS-3000

Отзывы:

Похожие инструкции для CS-3000

Бренды по названию

Популярные бренды

Echo CS-3000, Инструкция по эксплуатации

Результаты поиска

Содержание CS-3000

Отзывы:

Похожие инструкции для CS-3000

Бренды по названию

Популярные бренды