Echo CS-3000 TYPE 1E Скачать руководство пользователя

Страница: 1 / 24

Chain Saw

Operator’s Manual

MODELS :

CS-3000 TYPE 1E
Serial Number 2994 - 4033

CS-3400 TYPE 1E
Serial Number 3417 - 3941

CS-3450 TYPE 1E
Serial Number 4321 - 5119

WARNING

DANGER

WARNING

The engine exhaust from this

product contains chemicals known

to the State of California to cause

cancer, birth defects or other

reproductive harm.

Read rules for safe operation and instructions carefully. ECHO provides an Operator’s
Manual and an Engine Operator’s Manual. Both must be read and understood for proper
and safe operation.

Always keep clear of exhaust and muffler area,
otherwise serious personal injury may occur.

The muffler or catalytic muffler
and surrounding cover may become
extremely hot.

WARNING

DANGER

X7503202003

89865039233
06/02

Содержание CS-3000 TYPE 1E

























Результаты поиска

Содержание CS-3000 TYPE 1E

Отзывы:

Похожие инструкции для CS-3000 TYPE 1E

Бренды по названию

Популярные бренды

Echo CS-3000 TYPE 1E, Руководство оператора

Результаты поиска

Содержание CS-3000 TYPE 1E

Отзывы:

Похожие инструкции для CS-3000 TYPE 1E

Бренды по названию

Популярные бренды