background image

1

8 INCH CHIPPER

ENGLISH

Section

1.  Read and understand this owner’s manual. Be 

completely familiar with the controls and the proper 

use of this equipment.

2.  Familiarize yourself with all of the safety and 

operating decals on this equipment and on any of its 

attachments or accessories.

3.  Keep safety decals clean and legible. Replace 

missing or illegible safety decals.

4.  Obtain and wear safety glasses 

and use hearing protection at all 

times when operating this machine.

5. 

Avoid wearing loose fitted clothing. 

Never operate this machine while 

wearing clothing with drawstrings that could wrap 

around or get caught in the machine.

6.  Do not operate this machine if you are under the 

influence of alcohol, medications, or substances that 

can affect your vision, balance or judgement. Do not 

operate if tired or ill. You must 

be in good health to operate this 

machine safely.

7.  Do not operate this equipment in 

the vicinity of bystanders. Keep 

the area of operation clear of all persons, particularly 

small children. It is recommended that bystanders 

keep at least 50 feet (15 meters) away from the area 

of operation. 

8.  Do not allow children to operate this equipment.
9. 

Use only in daylight or good artificial light.

10. Do not run this equipment in an enclosed area. Engine 

exhaust contains carbon monoxide gas, a deadly 

poison that is odorless, colorless and tasteless. 

Do not operate this equipment in or near buildings, 

windows or air conditioners.

SAFETY

Indicates an imminently hazardous situation that, if not 

avoided, will result in death or serious injury.

DANGER

Indicates a potentially hazardous situation that, if not 

avoided, could result in death or serious injury.

WARNING

Indicates a potentially hazardous situation that, if not 

avoided, may result in minor or moderate injury.

CAUTION

The Owner/Operator’s manual uses this symbol to alert 

you of potential hazards. Whenever you see this symbol, 

read and obey the safety message that follows it. Failure 

to obey the safety message could result in personal injury, 

death or property damage.

1.1 SAFETY ALERT SYMBOL

1.2 BEFORE OPERATING

Содержание CH8540




























Отзывы: