16
oPERATIng
Operating Instructions
• Turn on water supply at the faucet to
completely open.
• Make sure the “ON/OFF” switch is in
the “OFF” position. The power switch
has international symbols for ‘on’ and
‘off’: On (|) Off (O).
• Unwind the power cord completely
and plug the GFCI into a grounded
120 volt outlet.
• Release safety push trigger lock up
and back into trigger. While pointing
the spray gun in a safe direction, squeeze the trigger on the spray gun
until there is a steady stream of water, letting the water and air out of
the hose. Push trigger lock back down to lock back into place.
• Turn the power switch to the “ON”
(|) position. The unit will turn on for
1 - 2 seconds and shut off. This is a
normal function of the auto start fea-
ture. Squeeze the spray gun trigger
to begin pressure washing.
• Begin power washing by squeezing
the trigger on the spray gun all the
way into the handle.
• Release the spray gun trigger to stop the power washer
• Allow the motor to come to a complete stop before squeezing the trig-
ger again.
• Squeezing rapidly will cause the auto start feature to miss an on/off
cycle that may prevent it from turning on while squeezing trigger after
rapid squeezing. Use slow deliberate
trigger pulls to avoid such symptoms.
Always
test a small area to avoid
chance of damaging the surface.
10
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
• Turn on water supply at the faucet to completely
open.
• Make sure the “ON/OFF” switch is in the “OFF”
position. The power switch has international symbols
for ‘on’ and ‘off’: On (|) Off (O).
• Unwind the power cord completely and plug the GFCI
into a grounded 120 volt outlet.
• Release safety push trigger lock up and back into
trigger. While pointing the spray gun in a safe
direction, squeeze the trigger on the spray gun until
there is a steady stream of water, letting the water
and air out of the hose. Push trigger lock back down
to lock back into place.
OFF/0
ON/I
OFF/0
ON/I
• Turn the power switch to the “ON” (|) position. The
unit will turn on for 1 - 2 seconds and shut off. This is
a normal function of the auto start feature. Squeeze
the spray gun trigger to begin pressure washing.
• Begin power washing by squeezing the trigger on the
spray gun all the way into the handle.
• Release the spray gun trigger to stop the power
washer
• Allow the motor to come to a complete stop before
squeezing the trigger again.
• Squeezing rapidly will cause the auto start feature to
miss an on/off cycle that may prevent it from turning
on while squeezing trigger after rapid squeezing. Use
slow deliberate trigger pulls to avoid such symptoms.
•
Always test
a small area to avoid chance of damaging
the surface.
10
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
• Turn on water supply at the faucet to completely
open.
• Make sure the “ON/OFF” switch is in the “OFF”
position. The power switch has international symbols
for ‘on’ and ‘off’: On (|) Off (O).
• Unwind the power cord completely and plug the GFCI
into a grounded 120 volt outlet.
• Release safety push trigger lock up and back into
trigger. While pointing the spray gun in a safe
direction, squeeze the trigger on the spray gun until
there is a steady stream of water, letting the water
and air out of the hose. Push trigger lock back down
to lock back into place.
OFF/0
ON/I
OFF/0
ON/I
• Turn the power switch to the “ON” (|) position. The
unit will turn on for 1 - 2 seconds and shut off. This is
a normal function of the auto start feature. Squeeze
the spray gun trigger to begin pressure washing.
• Begin power washing by squeezing the trigger on the
spray gun all the way into the handle.
• Release the spray gun trigger to stop the power
washer
• Allow the motor to come to a complete stop before
squeezing the trigger again.
• Squeezing rapidly will cause the auto start feature to
miss an on/off cycle that may prevent it from turning
on while squeezing trigger after rapid squeezing. Use
slow deliberate trigger pulls to avoid such symptoms.
•
Always test
a small area to avoid chance of damaging
the surface.
10
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
• Turn on water supply at the faucet to completely
open.
• Make sure the “ON/OFF” switch is in the “OFF”
position. The power switch has international symbols
for ‘on’ and ‘off’: On (|) Off (O).
• Unwind the power cord completely and plug the GFCI
into a grounded 120 volt outlet.
• Release safety push trigger lock up and back into
trigger. While pointing the spray gun in a safe
direction, squeeze the trigger on the spray gun until
there is a steady stream of water, letting the water
and air out of the hose. Push trigger lock back down
to lock back into place.
OFF/0
ON/I
OFF/0
ON/I
• Turn the power switch to the “ON” (|) position. The
unit will turn on for 1 - 2 seconds and shut off. This is
a normal function of the auto start feature. Squeeze
the spray gun trigger to begin pressure washing.
• Begin power washing by squeezing the trigger on the
spray gun all the way into the handle.
• Release the spray gun trigger to stop the power
washer
• Allow the motor to come to a complete stop before
squeezing the trigger again.
• Squeezing rapidly will cause the auto start feature to
miss an on/off cycle that may prevent it from turning
on while squeezing trigger after rapid squeezing. Use
slow deliberate trigger pulls to avoid such symptoms.
•
Always test
a small area to avoid chance of damaging
the surface.