Echo 77412 Скачать руководство пользователя страница 30

Страница: 30 / 43

4.5 INCH CHIPPER

SERVICE & MAINTENANCE

BEFORE INSpECTING OR SERvICING ANy pART OF THIS mACHINE, SHuT OFF pOWER SOuRCE,

DISCONNECT SpARk pLuG WIRE FROm SpARk pLuG AND mAkE SuRE ALL mOvING pARTS HAvE COmE TO A COmpLETE STOp.

Warning

rear drive belT

move the engagement lever to the RELEASE posi-

tion.
Disengage pTO and shut off tractor engine.

Remove the pTO shaft from the tractor and disconnect

from the 3 point hitch.
Remove the forward belt shield by removing the eight

5/16" x 3/4" bolts and washers securing the shield to

the chipper housing.
Loosen the eye bolt to release tension on the belt

(Figure 30).
Remove the 3/8" x 3-1/2" hex bolt, washer and nut

securing the idler pulley to the idler weldment. Remove

the idler pulley.
Remove the 3/8" x 4" hex bolt, washers, spacers and

nylock nut securing the idler weldment to the chipper

housing. move the idler weldment out of the way.
Remove the old belt and install the new belt.

Reattach the idler weldment to the chipper housing.

Reattach the idler pulley to the idler weldment.

10.

Tighten the eye bolt until the belt deflection is 7/16"

11.

when a 20 lb. load is placed against the belt.
Reinstall the forward belt shield using eight 5/16" x

12.

3/4" bolts and washers.

Figure 30, Rear belt drive replacement

4.6.1 engine modelS

removing The old bearingS

1. place the chipper engagement lever in the START

position.

2.  Shut engine off.
3.  Disconnect battery cables (electric start models).
4.  Remove the belt guard by removing the 5/16" bolts.
5.  Remove the idler pulley.
6.  place the chipper engagement lever in the CHIppING

position.

7. For models 77412 and 77412S, the belt guide will

have to be removed. To do this, remove the 1/2" bolt

attaching the belt guide to the rotor bearing and the

5/16" bolt attaching the belt guide to the engine.

8. Remove the belt.
9. To remove the rotor sheave, do the following:

9a. Remove the three bolts securing the rotor sheave

to the rotor shaft.

9b. Reinstall the bolts into the second set of holes.

Gradually tighten bolts equally to push the sheave

off the rotor shaft.

10. To remove the front bearing, do the following:

10a. Remove the snap ring.
10b. Loosen the setscrews securing the front bearing

to the rotor shaft.

10c. Remove the two 1/2" x 1-1/2" carriage bolts and

1/2" centerlock nuts holding the front bearing to

the chipper housing.

10d. Slide the front bearing off the rotor shaft.
10e. Remove the second snap ring.

11. To remove the back bearing do the following:

11a. Remove the seven 5/16" nylock nuts and wash-

ers securing the disk cover to the chipper hous-

ing. Remove the disk cover.

11b. Loosen the set screws securing the back bearing

to the rotor shaft.

11c. Remove the two 1/2" x 1-1/2" bolts and 1/2"

centerlock nuts holding the back bearing to the

chipper housing.

11d. Slide the chipper disk out from the chipper hous-

ing until the bearing slides off the rotor shaft.

4.5 drive belT rePlacemenT (conT.)

4.6 rePlacing roTor bearingS

Содержание 77412












































Результаты поиска

Содержание 77412

Отзывы:

Похожие инструкции для 77412

Бренды по названию

Популярные бренды

Echo 77412, Руководство пользователя

Результаты поиска

Содержание 77412

Отзывы:

Похожие инструкции для 77412

Бренды по названию

Популярные бренды